Fuel Plates
Mostrando 1-12 de 14 artigos, teses e dissertações.
-
1. Fases identificables en la zona de interacción de placas combustibles dispersas U3Si2/Al
ABSTRACT Fuel elements based on U3Si2 particles dispersed in a pure Al matrix (known as dispersion fuel element) are known to be very stable under irradiation, in plate type configurations. For this reason, they were or are being used to convert to low enriched uranium a large number of research reactors without significant loss in performance. According to
Matéria (Rio J.). Publicado em: 19/07/2018
-
2. Evaluation of the Influence of Surface Finishing on the Corrosion Resistance of HVOF Applied Inconel 625 Coatings on Steel
In this work, the corrosion resistance of Inconel 625 coatings applied to AISI 4140 steel plates was evaluated. Coatings were produced by High Velocity Oxygen Fuel (HVOF) by use of two different equipment which use either kerosene (liquid) or propane (gas) as fuel. The resulting coatings were evaluated in two conditions: as-deposited and after a surface fini
Mat. Res.. Publicado em: 18/12/2017
-
3. Microstructural Evolution and Mechanical Properties of Ni57Nb33Zr5Co5 Metallic Glass
The Ni57Nb33Zr5Co5 metallic glass is a promising alloy for bipolar plates in proton exchange membrane fuel cells. It is important to know which phase forms in this alloy under different cooling rates in order to understand its influence on the thermal stability and mechanical properties. In this work, melt-spun ribbons and rod samples with 1, 2 and 3 mm diam
Mat. Res.. Publicado em: 06/07/2017
-
4. Effect of Processing on Microstructure and Corrosion Mitigating Properties of Hydrotalcite Coatings on AA 6061 Alloy
Pitting corrosion of the aluminium cladding of spent nuclear fuels stored in light water pools has been observed. To prevent this, coating of the Al cladding with hydrotalcite (HTC) was proposed. This paper presents the effect of chemical bath and processing parameters on microstructure and corrosion behavior of HTC coatings on alloy AA 6061 specimens. The H
Mat. Res.. Publicado em: 03/11/2015
-
5. Trajectory Control During an Aeroassisted Maneuver Between Coplanar Circular Orbits
ABSTRACT: This paper presents the simulation results of an aeroassisted maneuver around the Earth, between coplanar circular orbits, from a geostationary orbit to a low orbit. The simulator developed considers a reference trajectory and a trajectory perturbed by external disturbances combined with non-idealities of sensors and actuators. It is able to operat
J. Aerosp. Technol. Manag.. Publicado em: 2014-06
-
6. Aplicação de métodos não destrutivos para qualificação de combustíveis tipo dispersão de U308-Al e U3Si2-Al no reator IEA-R1 / Application of non-destructive methods for qualification of the U3O8-Al and U3Si2-Al dispersion fuels in the IEA-R1 Reactor
IPEN/CNEN-SP manufactures fuels to be used in its nuclear research reactor the IEA-R1. To qualify those fuels, it is necessary to check if they have a good performance under irradiation. As Brazil doesnt have nuclear research reactors with high neutron fluxes, or suitable hot cells for carrying out post-irradiation examination of nuclear fuels, IPEN/CNEN-SP
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 24/11/2011
-
7. Procedimento de fabricação de elementos combustível a base de dispersão com alta concentração de urânio / Fabrication procedures for manufacturing high uranium concentration dispersion fuel elements
IPEN-CNEN/SP developed the technology to produce the dispersion type fuel elements for research reactors and made it available for routine production. Today, the fuel produced in IPEN-CNEN/SP is limited to the uranium concentration of 3.0 gU/cm3 for U3Si2-Al dispersion-based and 2.3 gU/cm3 for U3O8-Al dispersion. The increase of uranium concentration in fuel
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 11/11/2011
-
8. Determinação quantitativa da homogeneidade da distribuição de urânio em combustiveis nucleares tipo placa / Quantitative determination of uranium distribution homogeneity in MTR fuel type plates
O IPEN-CNEN/SP produz o combustível para suprir o seu reator nuclear de pesquisas IEA-R1. O combustível é montado a partir de placas combustíveis contendo um núcleo do compósito U3Si2-Al. Uma boa homogeneidade na distribuição de urânio no núcleo da placa combustível é essencial, pois garante um bom desempenho sob irradiação. Considerando a baix
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 03/05/2011
-
9. EVALUATION AND APPLICATION OF PEMFC FUEL CELL´S TECHNOLOGIES DEVELOPED AT IPEN APPLIED TO A 500 We FUEL CELL STACK / Avaliação e aplicação da tecnologia de células a combustível tipo pem desenvolvida no IPEN em um módulo de 500W de potência nominal
This work is part of a research project on PEMFC technologies carried out in IPEN to develop and optimize a 500 We fuel cell stack. The MEAs scaling up from 25 cm2 to 144 cm2 produced by the method of sieve printing; computational fluid dynamics by computer simulation of gas flow channels in bipolar plates using COMSOL® program and the use of Pt/C electrode
Publicado em: 2009
-
10. Mono and multi-layer electrolytes of ceria and zirconia prepared by tape casting / Eletrólitos mono e multicamadas de céria e zircônia preparados por colagem de fita
In this work it was investigated bi-layer electrolytes prepared by the tape casting technique. These electrolytes were composed of one layer of 10 mol% gadolinia doped ceria (CDG) and another one of 8 mol% yttria-stabilized zirconia (ZEI -8). CDG tapes were prepared with powder from Fuel Cell Materials (FCM) and powder obtained by oxide mixing. ZEI-8 tapes w
Publicado em: 2009
-
11. Desenvolvimento de técnicas para avaliação de combustíveis nucleares tipo placa pelo método de ensaio por ultra-som
One of the most important steps in the fabrication processes of plate type nuclear fuels, intended to be used in research reactors or naval propulsion, is the development of nondestructive testing (NDT) methods and techniques for their quality assessment during fabrication and post-irradiation analysis. Those tests can contribute to detect discontinuities su
Publicado em: 2008
-
12. Caracterização e classificação de placas de circuito impresso de computadores como residuos solidos / Characterization and classification of printed circuit boards of computer as solid residues
Equipments used in the data processing industry or entertainment they can contain more than 30% of printed circuit boards. These plates are formed by isoIated units and integrated and its scrap contains copper, lead, cadmium, zinc, tin, as well as the precious metals, gold, silver and platinum. Besides metals and metallic leagues, the printed circuit boards
Publicado em: 2002