Friction Factor
Mostrando 1-12 de 47 artigos, teses e dissertações.
-
1. THE PERFORMANCE OF EXPLICIT FORMULAS FOR DETERMINING THE DARCY-WEISBACH FRICTION FACTOR
ABSTRACT The Darcy-Weisbach equation is the most recommended equation for determining the pressure loss in pressurized pipes because of its wide applicability. However, one of the largest obstacles to implementing this equation is the friction factor (f) calculation. This factor can be precisely determined using the Colebrook equation, which is implicit. Thu
Eng. Agríc.. Publicado em: 2020-04
-
2. Towards Qualification of Friction Stir Welding to AA5083-O and AA5052-O Aluminum Alloys
Friction Stir Welding (FSW) is an excellent alternative for joining dissimilar and similar materials in comparison to conventional welding processes. In this sense, this work aims at qualifying FSW to similar AA5083-O and AA5052-O aluminum alloys, with 6.35 mm thickness, in a CNC machining center. Therefore, four welding experiments were undertaken. At first
Mat. Res.. Publicado em: 13/01/2020
-
3. Simulação de condição de fluxo em duto circular transportando polpa de bauxita de Paragominas (PA) na presença de aditivo modificador de viscosidade
RESUMO Sistemas de bombeamento de minérios por dutos tem atraído o interesse de mineradoras pois se tornam uma alternativa de transporte muito eficiente. Dentre os maiores desafios no projeto de bombeamento por dutos está a estimativa do fator de atrito, já que são muitas as variáveis que afetam este parâmetro. Uma amostra de polpa de bauxita de Parag
Matéria (Rio J.). Publicado em: 25/11/2019
-
4. Dry Sliding Wear Behaviour of Aluminium 5059/SiC/MoS2 Hybrid Metal Matrix Composites
The present study is to investigate the influence of weight percentage of silicon carbide (SiC) (5,10 %, 15%) and particle size (10,20,40µm) of SiC and constant 2% of Molybdenum disulphide(MoS2)is reinforced with aluminium matrix. Wear performance of the composite was carried out through pin-on-disc method to calculate friction coefficient and wear resistan
Mat. Res.. Publicado em: 28/09/2017
-
5. EXPERIMENTAL STUDY ON THE COLLABORATIVE DRAG REDUCTION PERFORMANCE OF A SURFACTANT SOLUTION IN GROOVED CHANNELS
Abstract Turbulence with a relatively larger vortex is obtained in drag-reducing surfactant solution, which provides an excellent condition for the application of small scale grooves. In this work, the coupling drag reduction performance of surfactant solution and grooves was experimentally investigated to explore the complementary possibility between their
Braz. J. Chem. Eng.. Publicado em: 2017-01
-
6. Application of optimization for improvement of the efficiency of louvered-fin compact heat exchangers
Abstract A few decades ago, the product development process was just based on a trial and error procedure, and the designer's experience. The need for a new way to design and manufacture more economical and sustainable products corroborates increasingly to a new vision of how to create new products for the benefit of society. Modern numerical tools allow gre
REM, Int. Eng. J.. Publicado em: 2016-09
-
7. Numerical and theoretical studies of bolted joints under harmonic shear displacement
A three-dimensional finite element model used to simulate the bolted joint is created using ABAQUS package. The stress concentration factors at the roots of the thread are first studied with a preload of 38.4 kN. Under harmonic transverse shear displacement, not only the stress variations at ten specified points of the first thread but also contact condition
Lat. Am. j. solids struct.. Publicado em: 2015-01
-
8. Effects of temperature-dependent viscosity on fluid flow and heat transfer in a helical rectangular duct with a finite pitch
An incompressible fully developed laminar flow in a helical rectangular duct having finite pitch and curvature with temperature-dependent viscosity under heating condition is studied in this work. Both the cases of one wall heated and four walls heated are studied. The cross-sectional dimensions of the rectangular duct are 2a and 2b. The aspect ratio n=2b/2a
Braz. J. Chem. Eng.. Publicado em: 2014-09
-
9. Analysis of equal channel angular extrusion by upper bound method and rigid blocks model
In present paper the Equal Channel Angular Extrusion (ECAE) through a rectangular die was firstly physically simulated using plasticine and then theoretically analyzed by upper bound method. Physical simulation was used to identify the deformation zone and as a background for the following theoretical ECAE analysis by rigid block model. The plane strain defo
Mat. Res.. Publicado em: 15/11/2013
-
10. Análise da convecção forçada no escoamento bidimensional laminar em dutos retangulares via GITT com variáveis primitivas. / Analysis of forced convection in two-dimensional laminar flow in rectangular ducts with via gitt primitive variables.
In the present study, forced convection flow in two-dimensional laminar simultaneous development pipeline with rectangular geometry, is analyzed analytically using the Navier-Stokes, Poisson and Energy in its primitive form. These equations are solved by the Generalized Integral Transform Technique, which is characteristic hybrid-numeric. The development wor
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 28/09/2012
-
11. Levantamento em campo da rugosidade equivalente de tubos metálicos / Field survey of the equivalent roughness of mettalic pipes
O objetivo deste trabalho é pesquisar e esclarecer as divergências dos valores de rugosidade equivalente de tubos comerciais de diferentes materiais, notadamente os de aço e ferro, que são mais comuns em aplicações industriais e de saneamento, no transporte de líquidos. Como estes valores muitas vezes não são coincidentes, apesar de originarem de ma
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 24/11/2011
-
12. 3D-CFD simulation and neural network model for the j and f factors of the wavy fin-and-flat tube heat exchangers
A three dimensional (3D) computational fluid dynamics (CFD) simulation and a neural network model are presented to estimate the behaviors of the Colburn factor (j) and the Fanning friction factor (f) for wavy fin - and - flat tube (WFFT) heat exchangers. Effects of the five geometrical factors of fin pitch, fin height, fin length, fin thickness, and wavy amp
Brazilian Journal of Chemical Engineering. Publicado em: 2011-09