Friction Evaluation
Mostrando 13-24 de 49 artigos, teses e dissertações.
-
13. Evaluation of the friction force generated by monocristalyne and policristalyne ceramic brackets in sliding mechanics
OBJETIVO: avaliar e comparar in vitro as cargas máximas de atrito geradas por três tipos de braquetes estéticos, sendo dois deles cerâmicos policristalinos convencionais (20/40 e InVu) e um monocristalino de safira (Radiance), em ambientes seco e umedecido por saliva artificial. Também avaliar a influência exercida pela saliva artificial sobre as carga
Dental Press J. Orthod.. Publicado em: 2013-02
-
14. Estudo do comportamento tribológico do aço AISI H13 submetido a tratamento termoquímico de boretação / Study of tribological behavior of AISI H13 steel subjected to boriding thermochemical treatment
In this work, solid boriding thermochemical treatment was carried out using Ekabor 1-V2 and one blend as boriding agents and heat treatment of quenching and tempering of AISI H13 tool steel in order to compare and evaluate the tribological behavior and the properties acquired for four studied conditions, that were: Ekabor powder boriding, Ekabor powder borid
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 18/06/2012
-
15. Evaluation of properties and FEM Model of the Friction welded mild Steel-Al6061-Alumina
Evaluation of mechanical and interfacial properties of friction welded alumina-mild steel rods with the use of Al6061 sheet are presented in this work. SEM, EDX analysis, hardness and bending strength tests were conducted. The bonds were attained through interfacial interlocking and intermetalllic phase formation with average bending strengths in the range o
Mat. Res.. Publicado em: 18/12/2012
-
16. On the evaluation of linear and non-linear models using DNS data of turbulent channel flows
In this paper, a priori and a posteriori analyses of algebraic linear and non-linear models are carried out in order to compare their ability to predict near wall turbulent flows. Tests were done using data from a direct numerical simulation (DNS) of a plane channel flow for three Reynolds numbers, based on the friction velocity, Reτ = 180, Reτ = 395 and R
J. Braz. Soc. Mech. Sci. & Eng.. Publicado em: 2012-12
-
17. Friction between different wire bracket combinations in artificial saliva: an in vitro evaluation
OBJECTIVE: The objective this work was to assess the friction coefficient between brackets and wires of different materials under conditions simulating the oral environment. MATERIAL AND METHODS: Stainless steel (SS) and titanium-molybdenum alloy (TMA) wires of 0.019x0.025-in diameter (American Orthodontics) and polycarbonate bracket (American Orthodontics),
Journal of Applied Oral Science. Publicado em: 2011-02
-
18. Avaliação da aderência pneu-pavimento e tendências de desempenho para a rodovia BR-290/RS / Evaluation and modeling of tire-road friction in brazilian federal road BR-290/RS
A aderência pneu-pavimento é um dos parâmetros mais importantes da segurança viária e deve ser avaliada em duas escalas: microtextura e macrotextura. As medidas de textura da superfície de pavimentos podem ser obtidas por diversos equipamentos, sendo que os mais difundidos são o Pêndulo Britânico e a Mancha de Areia. Dessa forma, esta pesquisa prete
Publicado em: 2011
-
19. Fungal microbiota isolated from healthy pig skin / Microbiota fúngica isolada da pele de suínos sadios
Background: Researches have been developed to observe the normal microbiota of different animal species. This subject is of major importance for the control of potential infection risks. Fungi can be found in various substrates, foodstuffs (cereals, meat, milk, vegetables) and also in the skin, mucosae, respiratory and gastrointestinal tracts of animals. Wit
Publicado em: 2011
-
20. A avaliação da grande área das ciências da saúde e as implicações para a formação de recursos humanos e produção de conhecimento na pós-graduação em educação física
In recent years, stricto-sensu graduate courses have been going through a growth process guided by policies that direct their operation and the strategies aiming at the insertion of the graduate system in the international arena. The principle of internationalization of scientific research is also present in the evaluation of stricto-sensu graduate programs
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 01/10/2010
-
21. Evaluation of frictional forces between ceramic brackets and archwires of different alloys compared with metal brackets
The aim of this study was to evaluate, in vitro, frictional forces produced by ceramic brackets and arch wires of different alloys. Frictional tests were performed on three ceramic brackets: monocrystalline (Inspire ICE), polycrystalline (InVu), polycrystalline with metal slot (Clarity), and one stainless steel bracket (Dyna-Lock). Thirty brackets of each we
Brazilian Oral Research. Publicado em: 2010-03
-
22. Analysis of numerically simulated true strain on high stampability sheets
The sheet metal forming is a manufacturing process widely used industrially. The quality and efficiency of the process is dependent on the correct choice of the process parameters and the correct understanding of the sheet metal behavior. The identification of the regions where stretching and/or deep drawing occurred during the forming process can aid the pr
Journal of the Brazilian Society of Mechanical Sciences and Engineering. Publicado em: 2010-03
-
23. Avaliação das forças, momentos e binding, produzidos por deformação de primeira ordem do fio NiTi .014 superelástico, em braquetes autoligáveis passivos estudo in vitro / Evaluation of force, moment and binding produced by first order deformation on a superelastic .014 Niti wire using passive self-ligated brackets in vitro study
Bracket characteristics and wire stiffness dictate the mechanical effects that nickel titanium wire deformation will cause upon teeth. The main variables associated to bracket characteristics include bracket length (that influence interbracket distance), and coefficient of friction. The purpose of this research was to compare how self ligated brackets such a
Publicado em: 2010
-
24. Considerações sobre o atrito para processos de forjamento a frio através do ensaio de compressão do anel
São realizadas análises teóricas e experimentais do atrito nos processos de forjamento a frio, através do ensaio de compressão do anel. Os modelos de atrito de Amonton-Coulomb (μ), atrito interfacial (m) e de Levanov (f) são investigados com auxílio de softwares comerciais de simulação de processos de forjamento. Diferentes condições de lubrifica
Publicado em: 2009