Fracture Behaviour
Mostrando 1-12 de 31 artigos, teses e dissertações.
-
1. Effects of Gas Nitriding on Fatigue and Crack Initiation of Ti6Al4V produced by Selective Laser Melting
Selective laser melting (SLM) is an additive manufacturing technique which permits fabrication of three dimensional parts by selectively melting consecutive layers of metallic powder. This allows the production of parts with high geometrical complexity. Titanium alloy Ti-6Al-4V (Ti64) is widely used in industry due to its high strength-to-mass ratio, corrosi
Mat. Res.. Publicado em: 15/07/2019
-
2. PM versus IM Ti-5Al-5V-5Mo-3Cr Alloy in Mechanical Properties and Fracture Behaviour
The comparisons of mechanical properties and fracture behaviour between as-consolidated PM Ti-5553 alloy and as-cast IM Ti-5553 alloy were investigated through tensile, fracture toughness and impact toughness tests in this research. The slightly higher strength but much higher ductility and toughness can be identified in IM alloy specimens, which is also con
Mat. Res.. Publicado em: 27/06/2019
-
3. Caracterización de daño por “b-value” de eventos de emisión acústica en ensayos de rotura de roca andesita
ABSTRACT Acoustic emission is a phenomenon that produces elastic waves when materials are subjected to tension. These waves spread towards the material surface where they are received by sensors that convert them into electrical signals for further analysis. In this work, acoustic emission signals were analysed in order to evaluate the amount of accumulated
Matéria (Rio J.). Publicado em: 19/07/2018
-
4. Effect of Heat Input on the Mechanical Behaviour of Al-Cu FSW Lap Joints
Dissimilar Al-Cu joints are desirable due to the combination of the good electrical and thermal properties of copper with the economic advantages of aluminium. However, different chemical, mechanical and thermal properties turn dissimilar welding into a challenge with traditional fusion welding techniques. Friction stir welding appears to be a good alternati
Mat. Res.. Publicado em: 28/05/2018
-
5. Acoustic Emission Analysis of Cement Mortar Specimens During Three Point Bending Tests
Abstract This work discusses the experimental results of Acoustic Emission (AE) recordings during repetitive loading/unloading loops of cement mortar beams subjected to three point bending. Six repetitive loading cycles were conducted at a gradually higher load level until the failure of the specimens. The experimental results clearly show the existence and
Lat. Am. j. solids struct.. Publicado em: 2016-12
-
6. An experimental investigation of static load capacity of AL-GFRP adhesively bonded single lap and double butt lap joints
AbstractThis paper is focused on experimental evaluation and comparison of progressive damage behaviors in adhesively bonded single lap and double butt lap joints between aluminum and glass fiber reinforced plastic (GFRP). The effect of joint design and dissimilarity of adherents on damage evolution of adhesive bonding under tensile quasi static loading is a
Lat. Am. j. solids struct.. Publicado em: 2015-08
-
7. Influence of local raw materials on the mechanical behaviour and fracture process of PVA-SHCC
This paper addresses the results of an investigation on the influence of the Brazilian raw materials on the mechanical performance of Strain Hardening Cementitious Composites (SHCC). The mixtures were produced with variations of fly ash/cement and sand/cement proportions and with different maximum sand particle. Mechanical properties were evaluated by direct
Mat. Res.. Publicado em: 08/10/2013
-
8. Workhardening behaviour and microstructural analysis of failed austenitic manganese steel crusher jaws
This study focussed on the work hardening behaviour and microstructure of austenitic manganese steel relative to premature failure of crusher jaws. Samples of sound and failed crusher jaws were taken, the change with depth from the working surface to the sample core was measured and their microstructures observed. The study revealed a sharp hardness gradient
Mat. Res.. Publicado em: 03/09/2013
-
9. Effect of the mechanical properties and mode loading on the mechanical behaviour of weldment: a numerical analysis
Welding is used to realize permanent assembly in mechanical structures to assure the continuity of the parts to be assembled contrary to the other assembly techniques which have physical or chemical discontinuities. Generally, crack evolution depends on several intrinsic and extrinsic parameters of material. The aim of this work is to analyse the severity of
Mat. Res.. Publicado em: 07/05/2013
-
10. Normalizing effect on fatigue crack propagation at the heat-affected zone of AISI 4140 steel shielded metal arc weldings
The fractography and mechanical behaviour of fatigue crack propagation in the heat-affected zone (HAZ) of AISI 4140 steel welded using the shielded metal arc process was analysed. Different austenitic grain size was obtained by normalizing performed at 1200 °C for 5 and 10 hours after welding. Three point bending fatigue tests on pre-cracked specimens along
Mat. Res.. Publicado em: 02/04/2013
-
11. Fracture mechanics of polymer mortar made with recycled raw materials
The aim of this work is to show that industrial residues could be used in construction applications so that production costs as well as environmental protection can be improved. The fracture properties of polymer mortar manufactured with recycled materials are investigated to evaluate the materials behaviour to crack propagation. The residues used in this wo
Materials Research. Publicado em: 2010-12
-
12. Nonlinear boundary element models to analyse fracture problems and reliability/optimization models applied to structures submitted to fatigue / Modelos não lineares do método dos elementos de contorno para análise de problemas de fratura e aplicação de modelos de confiabilidade e otimização em estruturas submetidas à fadiga
This work deals with the development of boundary element method (BEM) formulations to be used in engineering problems. Particular attention is given to using these formulations in development of reliability and optimization models applied to fatigue problems. Contributions to BEM formulations are developed, particularly, models that deal with crack growth in
Publicado em: 2009