Fotoelasticidade
Mostrando 25-36 de 54 artigos, teses e dissertações.
-
25. Distribuição de tensões em implantes dentários de diferentes desenhos utilizando fotoelasticidade
Differents drafts of tooth implant insert differents levels of tension in the surrounding bones. This can results in differents prognostics for the implants installed. This work considered by photoelasticity (resilience) of the circuit transmission the gradient of tensions produced in near pre-ordered of the implants when installed in photoelasticity matrix.
Publicado em: 2007
-
26. A Metodology for Evaluation of a Pilar Screw of a Dental Implant Using The Automatizated Plane Photoelasticity Technique / Uma metodologia para avaliaÃÃo do parafuso pilar em implantes dentÃrios usando fotoelasticidade automatizada
O parafuso pilar à um importante elemento constituinte de implantes dentÃrios convencionais. Ele à utilizado para fixar o pilar ou intermediÃrio ao implante. Em implantes dentÃrios convencionais, o nÃvel de torque aplicado à da ordem de 20 Ncm, porÃm sabe-se que o parafuso pilar resiste a maiores nÃveis de torque, e que uma maior prÃ-carga aplicada
Publicado em: 2007
-
27. Uma metodologia para avaliação do parafuso pilar em implantes dentários usando fotoelasticidade automatizada / A Metodology for Evaluation of a Pilar Screw of a Dental Implant Using The Automatizated Plane Photoelasticity Technique
The pillar screw is an important element of conventional dental implants. It is used to fix the pillar or intermediary to the implant set. In conventional dental implants, the torque level applied is near of 20 Ncm, however it knows that the pillar screw resists to bigger torque levels, and that a high pre-load could improve its setting. Many problems relate
Publicado em: 2007
-
28. DistribuiÃÃo das tensÃes geradas em implantes interconectados com barra dolder, apÃs solda a laser
PrÃteses implanto-retidas, necessitam de passividade e justeza no seu assentamento sendo considerados prÃ-requisitos para o sucesso da osseointegraÃÃo. Para minimizar distorÃÃes e promover assentamento passivo utiliza-se o corte e solda das infra-estruturas metÃlicas. Este estudo investigou, por meio da fotoelasticidade, a distribuiÃÃo de tensÃes g
Publicado em: 2007
-
29. Distribuição das tensões geradas em implantes interconectados com barra dolder, após solda a laser
The Implant-retained prostheses need passivity and justness in their settlement, which are considered prerequisites for the osseointegration success. To minimize distortions and to promote passive settlement it is used the cut and solder of the piece. This work investigated, through photoelasticity, the distribution of stress generated by implants interconne
Publicado em: 2007
-
30. Estudo fotoelástico da distribuição de tensões em implantes hexágono externo interconectados por resina acrílica e metal
The clinical success of dental implants has as important factor the way the mechanical stress is transferred from the implant the surrounding bone tissue. This transference and its magnitude may be related to the material of the screwed the prosthesis to the implants, risking the longevity of osseointegration. This study has as proposal to determinate the st
Publicado em: 2007
-
31. Estudo da transmissão e distribuição de tensões aplicadas à resina acrílica convencional e acrescida de fibras através do método fotoelástico / Study of tension transmission and distribution applied upon acrylic conventional resin and strengthened by fibers through photoelastic method
A resina acrílica encontra-se entre os materiais mais utilizados na odontologia. Apesar de suas qualidades, o polimetilmetacrilato ainda mostra-se um material com resistência comprometida. Para tanto, diversos reforços têm sido propostos na literatura e entre eles encontram-se as fibras de vidro e aramida. Apesar de acrescerem na resistência da matriz a
Publicado em: 2007
-
32. Analise fotoelastica das tensoes induzidas por estruturas de protese sobre implantes fabricadas pelas tecnicas monobloco, soldagem de borda e metodo CAD/CAM / Photoelastic analysis of tensions induced over implant superstructures manufactured through CAD/CAM method, border soldering and one-piece technique
A falta de passividade de infra-estruturas protéticas implantossuportadas pode acarretar problemas mecânicos e biológicos de grande importância. A proposta deste trabalho foi avaliar, pela técnica da fotoelasticidade, a tensão após o torque de estruturas metálicas protéticas implantossuportadas. Simulando a curvatura de uma mandíbula humana, foi co
Publicado em: 2007
-
33. Photoelastic analysis of tensions induced over implant superstructures manufactured through CAD/CAM method, border soldering and one-piece technique / Analise fotoelastica das tensoes induzidas por estruturas de protese sobre implantes fabricadas pelas tecnicas monobloco, soldagem de borda e metodo CAD/CAM
A falta de passividade de infra-estruturas protéticas implantossuportadas pode acarretar problemas mecânicos e biológicos de grande importância. A proposta deste trabalho foi avaliar, pela técnica da fotoelasticidade, a tensão após o torque de estruturas metálicas protéticas implantossuportadas. Simulando a curvatura de uma mandíbula humana, foi co
Publicado em: 2007
-
34. Photoelastic analysis of the effect of spark erosion procedure and screw tightening on implant framework / Analise fotoelastica do efeito da eletroerosão e sequencias de apertos de parafusos em infra-estrutura implanto-suportada
O presente estudo avaliou através de análise fotoelástica a passividade de infra-estrutura fundida em titânio, antes e após a aplicação de eletroerosão. Foi confeccionada uma matriz metálica simulando uma mandíbula humana onde foram implantados cinco análogos de pilares Micro-Unit (Conect ? AR, Conexão Sistemas de Prótese). A partir de um molde
Publicado em: 2006
-
35. Analise fotoelastica da distribuição de tensões induzidas por infra-estruturas implanto-suportadas apos soldagem a laser ou retificação de cilindros
This study evaluated two techniques indicated to obtain implant-supported fixed prostheses with satisfactory passive fit by means of photoelastic analysis. Two titanium casts groups were fabricated in a metallic master cast: Group I ? three frameworks fabricated by laser welded cylinder technique and Group II ? three frameworks cast in one-piece and submitte
Publicado em: 2005
-
36. Biomechanics load transmission single implants according to prosthetic materials photoelastic and dinamic analysis / "Biomecânica da transmissão de cargas a implantes unitários em função dos materiais protéticos: análise fotoelástica e dinâmica"
Less rigid oclusal materials such as acrylic resins are often used in prosthesis over implants because they are supposed to diminish the loads transferred to the bone; however there is no scientific evidence to support this theory. The objective of this work was to compare by photoelastic and dynamic analysis the load transfer after oclusal loads over single
Publicado em: 2005