Force And Roughness
Mostrando 1-12 de 112 artigos, teses e dissertações.
-
1. Morphology Behavior of Copper Films Deposited after Wet Surface Treatment on Polished Alumina
In this paper, a pre-treatment process for electroless copper (Cu) deposition on the polished alumina (Al2O3) 99.9% and the behavior of Cu plating by electroless process after Al2O3 surface treatment were explored. Our work was carried out by changing the roughness of Al2O3 through micro-etching (coarsening), nucleation its surface by a two-step method (sens
Journal of the Brazilian Chemical Society. Publicado em: 2022
-
2. Synthesis of New Phenolic-Schiff Base and Its Application as Antioxidant in Soybean Biodiesel and Corrosion Inhibitor in AISI 1020 Carbon Steel
New Schiff base compound N, N’-bis-(4-hexadecanate)-salicylethylenediamine (named IM) was synthesized, and characterized via infrared and nuclear magnetic ressonance spectroscopies. IM was tested as corrosion inhibitor and antioxidant in soybean biodiesel. Corrosion studies were developed with AISI 1020 carbon steel in a three-step accelerated corrosion as
J. Braz. Chem. Soc.. Publicado em: 2020-03
-
3. Influence of cigarette smoke combined with different toothpastes on enamel erosion
Abstract: This in vitro study aimed to evaluate the effect of different toothpastes on dental enamel subjected to an erosive cycle with and without exposure to cigarette smoke. Bovine enamel specimens were randomly allocated into 12 groups (n = 12). For the in vitro simulation of smoking, half the groups underwent an exposure cycle of 20 cigarettes per day f
Braz. oral res.. Publicado em: 02/12/2019
-
4. Tensile and fatigue properties, machinability and machined surface roughness of Al-Si-Cu alloys
ABSTRACT In this paper, the aim was to determine if ASC91 (9 % Al, 1 % Cu) could be replaced with ASC73 (7 % Al, 3 % Cu) aluminium alloy, with presumably improved machinability due to lower silicon content (9 to 7 %) and retained mechanical properties due to a higher copper content (1 to 3 %). The test samples were excised from cylinder heads produced by the
Matéria (Rio J.). Publicado em: 16/09/2019
-
5. Influência do material da ferramenta de corte sobre a usinabilidade do aço ABNT 4340 no torneamento
RESUMO No presente trabalho procurou-se compreender os fenômenos associados à usinagem do aço ABNT 4340 utilizando ferramentas de corte de metal duro e cermet, ambas com geometria do quebra-cavaco para usinagem leve (LP) e média (MP). Nesse sentido, analisou-se a influência da variação do avanço, quebracavaco e o material da ferramenta de corte nos p
Matéria (Rio J.). Publicado em: 16/09/2019
-
6. Effect of surface roughness and lubrication on the friction coefficient in deep drawing processes of aluminum alloy aa1100 with fem analysis
ABSTRACT Friction between the interface workpiece and tooling has considerable importance in sheet metal forming operations; an accurate description of the friction is necessary to analyze and design new workpieces and tooling. This work suggests a methodology to determine and evaluate the mean coefficient of friction (COF) using the Finite Element Method (F
Matéria (Rio J.). Publicado em: 16/09/2019
-
7. Electrospinning synthesis and assessment of physicochemical properties and biocompatibility of cobalt nitrate fibers for wound healing applications
Abstract: The aim of this study was to develop polyurethane (PU) wound dressing incorporated with cobalt nitrate using electrospinning technique. The morphology analysis revealed that the developed composites exhibited reduced fiber and pore diameter than the pristine PU. The electrospun membranes exhibited average porosity in the range of 67% - 71%. Energy-
An. Acad. Bras. Ciênc.. Publicado em: 29/07/2019
-
8. Blood compatibility assessments of electrospun polyurethane nanocomposites blended with megni oil for tissue engineering applications
Abstract: Tissue engineering holds as a prominent technique to repair or replace the damaged human parts to recreate its native function. In this research, a novel scaffold based on polyurethane (PU) comprising megni oil was electrospun for tissue engineering applications. The obtained polyurethane blended with megni oil nanofibers were characterized by scan
An. Acad. Bras. Ciênc.. Publicado em: 19/06/2019
-
9. Influência do material da ferramenta de corte sobre a usinabilidade do aço ABNT 4340 no torneamento
RESUMO No presente trabalho procurou-se compreender os fenômenos associados à usinagem do aço ABNT 4340 utilizando ferramentas de corte de metal duro e cermet, ambas com geometria do quebra-cavaco para usinagem leve (LP) e média (MP). Nesse sentido, analisou-se a influência da variação do avanço, quebracavaco e o material da ferramenta de corte nos p
Matéria (Rio J.). Publicado em: 20/05/2019
-
10. Effect of surface roughness and lubrication on the friction coefficient in deep drawing processes of aluminum alloy aa1100 with fem analysis 1
ABSTRACT Friction between the interface workpiece and tooling has considerable importance in sheet metal forming operations; an accurate description of the friction is necessary to analyze and design new workpieces and tooling. This work suggests a methodology to determine and evaluate the mean coefficient of friction (COF) using the Finite Element Method (F
Matéria (Rio J.). Publicado em: 20/05/2019
-
11. Surface morphologic evaluation of orthodontic bonding systems under conditions of cariogenic challenge
Abstract: Orthodontic bonding systems are submitted to demineralization and remineralization dynamics that might compromise their surface smoothness, and favor biofilm aggregation and caries development. The aim of the present study was to evaluate the effects of a cariogenic challenge model (in vitro pH-cycling model) on the surface roughness and topography
Braz. oral res.. Publicado em: 25/04/2019
-
12. Surface Topography, Gloss and Flexural Strength of Pressable Ceramic After Finishing-Polishing Protocols
Resumo O objetivo deste estudo foi avaliar o efeito de diferentes protocolos de acabamento e polimento na rugosidade da superfície, brilho, resistência à flexão biaxial e morfologia de cerâmica prensada. Trinta discos de cerâmica (12x1 mm) foram produzidos e divididos em cinco grupos (n=6): CT- controle (glaze); DA- ponta diamantada de granulação fin
Braz. Dent. J.. Publicado em: 04/04/2019