Flexural Strength
Mostrando 1-12 de 311 artigos, teses e dissertações.
-
1. The influence of compositional variability of dimension stone residues on the properties of rustic porous ceramic tiles
Abstract This study analyzed how the compositional variability of dimension stone residues influences the characteristics of rustic porous ceramic tiles. The specimens were prepared by adding 20 wt% of dimension stone residue to the clay and sintered at 1000 °C for 1 h. The testing assays performed were physical properties and structural analysis through sc
Cerâmica. Publicado em: 2023
-
2. Influence of bottom ash and red mud additions on self-leveling underlayment properties
Abstract Self-levelling underlayments (SLUs) based on Portland cement (PC) are susceptible to cracking due to drying shrinkage. The present study evaluated the influence of binder contents on systems consisting of calcium aluminate cement (CAC), PC, and a source of calcium sulfate (C$), derived from the flue gas desulfurization process (FGD), on the mechanic
Cerâmica. Publicado em: 2022
-
3. Mechanical properties and fractography of cement-based composites reinforced by natural piassava and jute fibers
Abstract Today’s demand for environmentally friendly and energy-efficient solutions to the construction industry has driven researchers to match natural resources with traditional technics to develop new building technologies. However, there are literature limitations about the correlation of fiber-matrix interface with the failure of natural fibers in mor
Cerâmica. Publicado em: 2022
-
4. Effects of plaster to water ratio on physical and mechanical properties of ceramic pieces produced by the slip casting process
Abstract In the slip casting process, the relationship between the amount of plaster and water used in the production of molds influences the production of ceramic materials, because the higher the water content in the mixture, the lower the mechanical strength of the mold and higher the water absorption rate. In order to evaluate the influence of the variat
Cerâmica. Publicado em: 2022
-
5. Evaluation of the self-healing capacity of ceramics produced with alumina and silicon carbide
Abstract The self-healing capacity of a ceramic material produced by uniaxial pressing with alumina (Al2O3), silicon carbide (SiC), and magnesium oxide (MgO) was evaluated. To assess self-healing, a discontinuity was generated on the surface of the specimens. The healing time in the oven, at a temperature of 1000 ºC, was 1, 30, and 60 min. The specimens wer
Cerâmica. Publicado em: 2022
-
6. Manufacturing and characterization of sustainable macroporous glass foams
Abstract This work produced glass foams from soda-lime glass bottles, bentonite, and alumina by the replica method. Compositions with different contents of bentonite (5, 10, 15, and 20 wt%) were prepared and heat-treated at 800 °C. In the alumina-added compositions, 50 wt% of the bentonite was replaced by the alumina. The influences of the content of benton
Cerâmica. Publicado em: 2022
-
7. Influence of the physical characteristics of sand and the crushed filler content on the properties of self-leveling mortars
Abstract The properties of self-leveling mortars (SLMs) in the fresh and hardened state are strongly affected by their formulation. In this study, the influence of three different quartz sands (different physical characteristics) was investigated in SLMs, as well as the replacement of these sands by crushed basalt filler. The tests performed were: spreading,
Cerâmica. Publicado em: 2021-06
-
8. Evaluation of flexural strength and antibacterial effect of orthodontic acrylic resins containing Galla chinensis extract
RESUMO Objetivo: Avaliar se diferentes concentrações de extrato de Galla chinensis (EGC) adicionado ao polimetilmetacrilato (PMMA), que é amplamente utilizado para a fabricação de aparelhos ortodônticos removíveis, interferem no efeito antimicrobiano desse extrato e na resistência à flexão do PMMA. Métodos: Foram preparadas amostras de resina a
Dental Press J. Orthod.. Publicado em: 2020-12
-
9. Post-elastic Deformation Characteristics of Hybrid Fibre Reinforced Concrete Composites
Abstract The present study was focused on evaluating the strength and failure properties of hybrid micro-fibre concretes containing micro brass and steel fibre additions. Experimental tests were conducted on different hybrid fibre concretes containing aligned fibres in the direction of beam axis and the relative mechanical performance was compared to randoml
Lat. Am. j. solids struct.. Publicado em: 10/01/2020
-
10. Evaluation of the Effect of the Incorporation of Blends of Fuel and Fluxing Wastes in Red Clay Ceramics
The clay samples endure the incorporation of industrial and urban wastes, which do not cause large variations in their properties if added in controlled quantities. Wastes can be classified as fuel, fluxing and property affecting wastes. The fuel wastes usually have a high amount of organic matter, that when heated cause exothermic reactions, releasing heat
Mat. Res.. Publicado em: 09/12/2019
-
11. Glass-ceramic produced with recycled glass
ABSTRACT The objective of this work is the production and characterization of glass-ceramic with recycled glass powder and 4% (w/w) of cerium dioxide. Eleven groups were defined with conformation pressure of 11.6 and 25.8 MPa, and cerium dioxide addition. The sintering temperatures of 650, 675, 700 and 750 °C were used. The raw material was formed into a mo
Matéria (Rio J.). Publicado em: 25/11/2019
-
12. Bond strength evaluation between textiles reinforced mortar with carbon nanotubes and concrete substrate
Abstract The influence of using carbon nanotubes to improve bond strength between textiles reinforced mortar and concrete was investigated. Forty-two specimens were tested using double-shear test to evaluate the effect of various parameters such as CNTs addition, type of textile material, bond length and width, and number of TRM layers on the bond behavior.
Lat. Am. j. solids struct.. Publicado em: 25/11/2019