Finite Elements
Mostrando 13-24 de 590 artigos, teses e dissertações.
-
13. Smart Graphene-Based Frequency Selective Surface Designed to Act as Single or Dual Band Device with Reconfigurable Operation Bands
Abstract In this paper, a finite-difference time-domain (FDTD) formulation, based on the exponential matrix and on thin material sheet methods is developed for modeling subcellular thin graphene sheets. This formulation is validated by reproducing graphene frequency selective surfaces (FSS) known from literature. Then, we propose in this work a smart graphen
J. Microw. Optoelectron. Electromagn. Appl.. Publicado em: 11/11/2019
-
14. Structural models for analysis of reinforced concrete frame buildings with masonry infills
Resumo Este trabalho tem como objetivo o estudo do comportamento de pórticos de edifícios de concreto armado preenchidos com alvenaria frente às ações horizontais, empregando-se dois modelos estruturais: i) modelo de diagonal equivalente (MDE) e ii) modelo com elementos finitos bidimensionais para estado plano de tensões (MEF). No primeiro modelo, a al
Rev. IBRACON Estrut. Mater.. Publicado em: 11/11/2019
-
15. Nonlinear numerical analysis of composite slabs with steel decking
Resumo O comportamento das lajes mistas é governado pelo cisalhamento longitudinal na interface entre o aço e o concreto, que é desenvolvido em lajes sob flexão simples. O método m-k e o método da interação parcial, utilizados no cálculo da resistência ao cisalhamento na interface aço-concreto de lajes mistas, são baseados em ensaios experimentai
Rev. IBRACON Estrut. Mater.. Publicado em: 11/11/2019
-
16. Nonlinear static analysis of a pile-supported wharf
Resumo O objetivo deste artigo é desenvolver uma análise estática não-linear através de um estudo de caso de um cais sobre estacas situado em uma nova área portuária para petroleiras. A atividade sísmica da área é muito intensa com uma aceleração máxima do solo de 0.55 g. Por esta razão, é muito importante analisar o comportamento estrutural n
Rev. IBRACON Estrut. Mater.. Publicado em: 11/11/2019
-
17. Influencia de la geometría del proyectil en ensayos dinámicos de tracción
ABSTRACT The focus of this study is to discuss the influence of the projectile’s length on the results of an experiment of the Hopkinson Traction Bar (SHTB). Simulations have been made by means of finite elements using the commercial software ABAQUS in tests of traction at high speeds of deformation in samples of aluminum alloy 7017T73 varying the length o
Matéria (Rio J.). Publicado em: 16/09/2019
-
18. Experimental-numerical Technique to Evaluate the Thickness of TiN Thin Film
In this study, the numerical analysis of instrumented indentation testing was combined with the experimental procedure to evaluate the mechanical properties and thickness of a titanium nitride (TiN) film deposited on titanium substrate (Ti) by plasma processing. TiN film thickness is an important parameter for the surface treatment industry. In numerical ana
Mat. Res.. Publicado em: 09/09/2019
-
19. Optimized design of RC deep beams based on performance metrics applied to strut and tie model and in-plane stress conditions
Abstract Deep beams do not behave according to classical beam theory. The nonlinearity of strain distribution within these elements requires application of strut and tie models (STM) or other alternatives to evaluate the complex stress field. Although the design of these elements is a common task for structural engineers, limited research is found on assessi
Lat. Am. j. solids struct.. Publicado em: 22/08/2019
-
20. Some Aspects of Numerical Modeling of Steel-Concrete Composite Beams with Prestressed Tendons
Abstract Aspects about the numerical modeling of three-dimensional prestressed steel-concrete composite beams by using the finite element (FE) method are highlighted and commented in this work. Emphasis is given to the numerical treatment of bonded and unbonded tendons. The proposed modeling technique uses curved beam and catenary elements for simulating int
Lat. Am. j. solids struct.. Publicado em: 15/08/2019
-
21. Thermo-mechanical analysis of mass concrete elements made of rubberized concrete
Resumo Neste estudo, foram avaliadas amostras de concreto massa com borracha (concreto emborrachado) para determinar se a adição de partículas de borracha aumentaria a resistência à fissuração devido a variações volumétricas de origem térmica, em comparação com um concreto de referência, sem borracha. Amostras dos concretos estudados foram inic
Rev. IBRACON Estrut. Mater.. Publicado em: 18/07/2019
-
22. Vibration control device for steel tubular towers of Horizontal Axis Wind Turbines
Abstract This paper presents and discusses the design of a vibration control device for a 120 m high steel tubular tower of onshore Horizontal Axis Wind Turbine (HAWT). The tower is modeled using beam (own code), and shell and solid finite elements (via ANSYS). The Dynamic Vibration Absorber (DVA) is designed to be attached to the tower top, aiming to analyz
Lat. Am. j. solids struct.. Publicado em: 10/07/2019
-
23. Textual Artifact of Advertising: A Thrust of Halliday’s Mood System Resources
RESUMO Este artigo argumenta que a publicidade contém uma variedade de textos que terminologias teóricas são capazes de exemplificar. Assim, dez propagandas de bebidas, entre outros tipos, foram escolhidas para análise. Os recursos de mudança de tom de Halliday decompuseram os textos em componentes significativos, que posteriormente foram tabulados com
Rev. bras. linguist. apl.. Publicado em: 19/06/2019
-
24. Numerical approach of the steel-concrete bond behavior using pull-out models
ABSTRACT This paper deals with the analysis of monotonic loading behavior in pull-out tests. The main objective is to obtain a reliable numerical model to represent the steel-concrete bond behavior using previously obtained experimental results. The tests were performed in RILEM pull-out specimen using 10 mm steel bar and concrete with compressive strength o
Matéria (Rio J.). Publicado em: 10/06/2019