Fe Si Alloy
Mostrando 1-12 de 45 artigos, teses e dissertações.
-
1. Microstructure and Fracture of 50Mo-50Re Vacuum Brazed with Fe-Si-B Filler Metal
Microstructural evolution, interfacial reaction and fracture during vacuum brazing of 50Mo-50Re alloys using amorphous alloy Fe-5.6Si-2.6B(wt%) were investigated. A binary intermetallic compound, σ(Mo2Re3) formed as parallel contiguous layers in the diffusion zone. In addition, Fe from the braze alloy, in combination with dissolved Mo from the substrate, fo
Mat. Res.. Publicado em: 30/09/2019
-
2. Fabrication of Fe-2.1 wt.% Si Alloy Sheets with Dominant Goss Texture Through Thickness
Macro- and micro-texture of Fe-2.1 wt.% Si alloy sheets were investigated and analyzed by X-ray diffraction and electron backscattered diffraction techniques. A Goss ({110}<001>) component accompanied by extremely weak γ (<111>//ND, normal direction) fiber is successfully formed through the sheet thickness after primary recrystallization and considerable gr
Mat. Res.. Publicado em: 15/07/2019
-
3. Effects of Cold Rolling Deformation on Microstructure and Damping Capacity of a Fe-Mn-Cr-Co-Si Alloy
The microstructure evolution of Fe-19Mn-8Cr-1Co-0.2Si (wt.%) alloy and Fe-19Mn (wt.%) alloy during cold rolling and its effect on the damping capacity of the two alloys were investigated. It was shown that the damping capacity of the two alloys was enhanced significantly owing to the deformation-induced ε-martensite and stacking faults. The Fe-19Mn-8Cr-1Co-
Mat. Res.. Publicado em: 11/07/2019
-
4. Microstructure evolution during the extrusion of a 6351 aluminum alloy tube
Abstract The aluminum alloy AA 6351 is a precipitation hardened alloy of the Al-Mg-Si system, additionally containing Mn and Fe. In this study, the microstructural characterization during processing of a thick wall extruded AA 6351 tube was carried out. Several complementary techniques for microstructural characterization were used, such as polarized light o
REM, Int. Eng. J.. Publicado em: 19/06/2019
-
5. Consolidation of Fe-Based Metallic Glass Powders by Hot Pressing
An alternative route to obtain bulk metallic glasses is by consolidation of metallic glass powders by deforming these materials in the temperature interval between the crystallization temperature and the glass transition temperature, where the material flows with a reduced viscosity. In the present work, bulk parts of the Fe43.2Co28.8B19.2Si4.8Nb4 alloy were
Mat. Res.. Publicado em: 17/01/2019
-
6. Length Scale of the Dendritic Array Tailoring Strength of a 5052 Aluminum Alloy
The present research aims to characterize 5xxx alloy series, considering chemistries based on the commercial 5052 alloy with three Mg contents (2.4wt.%, 2.6wt.% and 3.2wt.%) through transient directional solidification experiments. Very representative incoming impurities to a given twin-roll casting procedure were reached. As such, the Si, Fe, Cu, Mn and Cr-
Mat. Res.. Publicado em: 03/12/2018
-
7. Relationship Between Aluminum-Rich/Intermetallic Phases and Microhardness of a Horizontally Solidified AlSiMgFe Alloy
An experimental study with an A356-AlSiMgFe alloy was developed to evaluate the microhardness performance in the microstructure resulting of an unsteady-state horizontal solidification process. The Al-7wt%Si-0.3wt%Mg-0.15wt%Fe alloy was elaborated and directionally solidified in a water-cooled horizontal solidification device. In order to experimentally dete
Mat. Res.. Publicado em: 23/11/2018
-
8. Efecto de los parámetros de aplicación en recubrimientos de Ni-Cr-B-Fe-Si obtenidos por Flame Spray
ABSTRACT Surface damage of components in service is an issue of great industrial interest because of the costs associated to the replacement of certain critical components. There are several techniques to generate coatings, which provide increased resistance to a particular type of surface damage. In this way, it is achieved surface protection to different s
Matéria (Rio J.). Publicado em: 02/08/2018
-
9. Obtención y caracterización de recubrimientos de biovidrio sobre la aleación de Mg AZ31
ABSTRACT The ideal material for a metal bone prosthesis must undergo a gradual corrosion in vivo, without releasing toxic components, while acting as a support and facilitating the growth of bone tissue, until a replacement is completed by the regenerated bone. . Biodegradable magnesium alloys have been studied because of their excellent mechanical propertie
Matéria (Rio J.). Publicado em: 19/07/2018
-
10. Microscopía fototérmica para el estudio de transformaciones de fase
ABSTRACT A novel system allowing a high spatial resolution mapping of the thermal diffusivity as a function of temperature up to 1800 K is presented. The system is based on a photothermal technique recently developed by the group, consisting in measuring, with a probe laser beam, the curvature induced by local heating with a modulated pump laser. A microscop
Matéria (Rio J.). Publicado em: 19/07/2018
-
11. Rheo-Squeeze Casting of High-Silicon Aluminium Alloy Pipes with Gradient Structures and Their Mechanical Properties
Three different compositions of high-Si Al alloy pipe, with a gradient structure, were produced through semi-solid rheological squeeze casting, the microstructural characteristics of which were investigated. The mechanism of gradient structure formation and the effect of acicular Fe-rich phases on liquid segregation were revealed. Meanwhile, the crystal stru
Mat. Res.. Publicado em: 11/06/2018
-
12. Study of Mechanical and Wear Behaviour of Hyper-Eutectic Al-Si Automotive Alloy Through Fe, Ni and Cr Addition
Effect of Fe, Ni and Cr addition on the wear behavior of hyper-eutectic Al-Si automotive alloy has been studied. Dry sliding wear tests have been conducted using pin-on-disc wear testing machine under normal loads of 20N and constant sliding speed of 0.64 ms-1. Influence of Fe addition to the base alloy increases the wear rate due to the formation of needle
Mat. Res.. Publicado em: 11/06/2018