Fcaw G Process
Mostrando 1-7 de 7 artigos, teses e dissertações.
-
1. Performance of the INCONEL 625 alloy weld overlay obtained by FCAW process
ABSTRACT Nickel-based weld overlays (cladding) are commonly used in oil & gas industry to extend the life of equipment under corrosive environment, as it improves the corrosion resistance without a significant increase in the manufacturing cost, when compared to a full nickel-based alloy equipment. Although there are extensive literature involving overlays a
Matéria (Rio J.). Publicado em: 20/05/2019
-
2. Evenmatched FCAW process in API 5L X80 steel welded joint
The evenmatched welding conditions in FCAW-G process were used in API 5L X80 steel. In this study, two joint geometries (bevel 25° and 35°) with different process parameters were used. Each type of joint was welded with one type of consumable: AWS E81T1-Ni1C (evenmatched), with variation of heat input. During welding the voltage and current varied in a ran
Mat. Res.. Publicado em: 24/01/2014
-
3. Efecto del calor aportado en recargues nanoestructurados base hierro
In the last years there have been developed several consumables that deposit hard nanostructured iron-based metals with high resistance to abrasive wear. The erosive and abrasive wear resistances are mainly controlled by the chemical composition and the microstructure. In turn, the microstructure of the deposited metal usually shows variations with the exper
Soldag. insp.. Publicado em: 2013-12
-
4. Análise da influência dos parâmetros de operação sobre a geometria do cordão de solda obtido pelo processo de soldagem por eletrodo tubular / Analysis of the influence of welding parameters on the geometry of the weld bead obtained by the process of welding tubular electrode
Este trabalho tem por finalidade a análise dos parâmetros de soldagem do processo com eletrodo tubular com proteção gasosa (FCAW-G – Flux Cored Arc Welding Gas-Shielded) sobre as características geométricas do cordão de solda (largura do cordão, altura do cordão e penetração). As variáveis do processo analisadas foram tensão, velocidade de ali
Publicado em: 2011
-
5. Aplicação de revestimento duro utilizando o processo arame tubular com e sem adição de arame não energizado para diferentes tipos de consumíveis / Hardfacing application using the FCAW process with and without not-energized wire addition for different kind of consumables
O cultivo de cana-de-açúcar é uma das maiores atividades agropecuárias do Brasil proporcionando um forte mercado de produção e exportação de etanol e açúcar. Um dos fatores que afetam os custos do processo da indústria sucroalcooleira é a manutenção dos equipamentos afetados por danos relacionados à perda de metal (massa) por mecanismos de des
Publicado em: 2011
-
6. Estudo da soldabilidade do tubo API 5L X80 utilizando os processos de soldagem: MAG com transferência controlada e eletrodo tubular. / Study of the weldability of API 5L X80 pipe using the gmaw-stt and fcaw welding process.
Os tubos API 5L X80, construídos com aços alta resistência e baixa liga, são especificados para a construção de dutos para transporte de petróleo e derivados sob alta pressão, com conseqüente redução no peso dos tubos. O processo mais empregado para a soldagem circunferencial de tubos em campo no Brasil é o processo com eletrodo revestido, tanto
Publicado em: 2010
-
7. WELDABILITY ANALISES OF API 5L X-80 STEEL USING TEKKEN TEST AND IMPLANT TEST / ANÁLISE DA SOLDABILIDADE DO AÇO API 5L X-80 POR MEIO DOS TESTES TEKKEN E DE IMPLANTE
This work shows a study of the weldability of API 5L X-80 steel using the Tekken Test and the Implant Test. The research analises the weldability of HSLA X-80 steel for orbital circunferencial welding with the Shielded Metal Arc Weld and the Flux Core Arc Weld processes with regard to hydrogen induced cracking formation. The aim is to make feasible different
Publicado em: 2008