Face Milling
Mostrando 1-12 de 24 artigos, teses e dissertações.
-
1. Fresamento com ar quente: uma proposta para minimizar a formação de trincas térmicas em ferramentas de metal duro
This work presents the results, analyses and conclusions about a study carried out with objective of minimizing the thermal cracks formation on cemented carbide inserts during face milling. The main focus of investigation was based on the observation that milling process is an interrupted machining process, which imposes cyclic thermal loads to the cutting t
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 29/07/2011
-
2. Uma contribuição ao fresamento frontal de superfícies irregulares em blocos de motores em ferro fundido cinzento / A contribuition to the face milling of irregular grey cast iron surface
Atualmente a competitividade das empresas é um objetivo que vem sendo buscado de forma bastante intensa. Por outro lado, fatores como o meio ambiente e a preocupação com o conforto e a saúde dos seus colaboradores também tem sido motivo de preocupação. Esses dois fatores são as vezes antagônicos e para conseguir atingi-los simultaneamente é necess�
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 01/07/2011
-
3. Comportamento da rebarba no fresamento de faceamento do aço inoxidável PH 13 8Mo / Behavior of the Burr in Face Milling of PH 13 8Mo Stainless Steel
Esta tese tem o objetivo de investigar a formação das rebarbas no fresamento de faceamento do aço inoxidável PH 13 8Mo. Foram utilizados insertos de metal duro intercambiáveis numa fresa de diâmetro de 63 mm. Os ensaios foram divididos em duas etapas. Na primeira etapa foram consideradas as seguintes variáveis: aplicação do fluido de corte, geometri
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 03/06/2011
-
4. Estudo das forças, vibrações e desgaste das ferramentas no fresamento da liga de titânio Ti-6A1-4V / A study about forces, vibration and tool wear in Ti-6A1-4V titanium alloy face milling
Ligas de titânio já apresentam um papel de grande importância na indústria aeroespacial, petroquímica e de biomateriais. A combinação de alta resistência mecânica, baixa densidade, resistência à corrosão, biocompatibilidade, boa tolerância tecidual e manutenção de suas características em altas temperaturas, configuram o titânio como um mater
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 07/02/2011
-
5. Performance of carbide and ceramic tools in the milling of compact graphite iron - CGI
Grey cast iron (GCI) is the most common material used in diesel engine blocks. However, to increase the pressures in the combustion chamber when this kind of alloy is used, it is necessary to increase the block wall thickness, what raises its weight and, consequently, does not fulfill the requirements. Thus, the compacted graphite iron (CGI) appears as an al
Journal of the Brazilian Society of Mechanical Sciences and Engineering. Publicado em: 2010-12
-
6. Estudo dos esforços de corte no processo HSM aplicado à abertura de cavidades / Study of the cutting forces in HSM process applied to pocket milling
The manufacturing of a great number of components in the industry depends on molds and dies used in processes like forging, powder metallurgy, deep drawing, casting and plastic injection. One of the main operations for manufacturing of these parts corresponds to the opening of the initial pocket, from which more complex geometries are machined in order to ob
Publicado em: 2010
-
7. Estudo das contaminações provenientes do processo de cominuição de amostras geológicas / A study of contaminations derived from comminution processes of geologic samples
A cominuição de amostras geológicas envolve etapas para reduzir seus grãos garantindo sua representatividade, com o auxílio de vários equipamentos de moagem de amostras. São duas as contaminações que podem ser causadas durante o uso desses equipamentos. A primeira é a contaminação primária, pelo contato face a face entre a amostra e os component
Publicado em: 2010
-
8. Optimization of the cutting conditions (Vc, fz and doc) for burr minimization in face milling of mould steel
The aim of the present work is to investigate the burr formation mechanisms at the edges (lateral and exit) during face milling of mould steel using carbide tools. The effects of the cutting parameters were studied and strategies of burr minimization were discussed. The proposed minimization was achieved by optimizing the cutting conditions: cutting speed (V
Journal of the Brazilian Society of Mechanical Sciences and Engineering. Publicado em: 2009-06
-
9. Uma contribuição para o estudo das deformações residuais proporcionadas pelo processo de usinagem por fresamento. / A contribution for residual deformation study originated by the face milling machining process.
The face milling operation purpose is providing flat machined surfaces free from residual strains at the cross section of the workpiece. On the other hand, the evidences presented in this thesis are enough to demonstrate that the strain exists and its behavior can be related to technical measurements such as the cutting tool helical profile, the feed rate, t
Publicado em: 2009
-
10. Study of laser textured and coated cutting tools used in face milling of compacted graphite cast iron / Estudo da caracterização de ferramentas de corte texturizadas a laser e revestidas utilizadas no fresamento frontal de ferro fundido vermicular
The controlled alteration of a surface can improve the performance of a mechanical part. The texture is the digital impression of a surface composed of hills and cavities, normally disordered distributed. When this texture is uniform and regularly distributed on a surface, it can modify significantly the functionality of a component. A technique used to unif
Publicado em: 2009
-
11. Uma contribuição a melhoria do processo de fresamento de ferro fundido vermicular - CGI / A contribution to the improvement of the milling process machining compacted graphite iron - CGI
Since the beginning of this century, researches about the development of diesel engines have been intensified, aiming to increase its energy efficiency and to reduce the levels of emission of pollutants. One the way to increase this efficiency is to increase the peaks of pressure of fuel explosion in the combustion chamber. The grey casting iron material is
Publicado em: 2009
-
12. Investigação sobr o uso da texturização a laser na preparação da superficie a ser recoberta em ferramentas de metal duro para fresamento / Research on the use of laser texturing for the surface preparation of to be coated carbide milling tools
Machining is one of the fundamental manufacturing processes of contemporary industry and coated cemented carbide is the most used cutting tool material. Manufacturing of this kind of tools includes the substrate surface processing previously to coating deposition in order to achieve high adhesion resistance in the substrate-coating interface. The most spread
Publicado em: 2009