Electron Microscopy
Mostrando 13-24 de 9551 artigos, teses e dissertações.
-
13. Influence of the addition of niobium oxide on the properties of fused aluminum oxide used in abrasive tools
Abstract Fused alumina is a material used in the manufacturing of abrasive tools, due to its high fusion point, great hardness, and mechanical toughness. In this context, this study addressed the influence of niobium addition on the properties of fused alumina for abrasive applications. A comparison was also made between this oxide and the brown fused alumin
Cerâmica. Publicado em: 2022
-
14. EFFECT OF REACTION CONDITIONS ON PARTICLE SIZE OF ZNO NANOPARTICLES VIA CONTROLLED PRECIPITATION METHOD AND IN-VITRO ANTIBACTERIAL CAPACITY
High-yield ZnO spheroidal nanoparticles with an average diameter around 23 nm (≈ 25% frequency) and 30 nm (≈ 28% frequency) were obtained by controlled semicontinuous precipitation at low temperatures. This synthesis was obtained from hydrozincite (Zn5(CO3)2(OH)6) as primary nanoparticles. The Zn5(CO3)2(OH)6 nanoparticles were synthesized by hydrolysis o
Química Nova. Publicado em: 2022
-
15. Phase transformation of kaolinite to hexagonal kalsilite using K2CO3
Abstract Hydrothermal synthesis of kalsilite was facilitated by the inclusion of potassium carbonate (K2CO3) as the source of the potassium ion. After a 24 h reaction at 220 °C, kaolin clay treated with 1.25 M K2CO3 showed the most significant peaks at 2θ of 28.5° and 34.7° by X-ray diffraction corresponding to the hexagonal kalsilite. In addition, field
Cerâmica. Publicado em: 2022
-
16. Mechanical properties and fractography of cement-based composites reinforced by natural piassava and jute fibers
Abstract Today’s demand for environmentally friendly and energy-efficient solutions to the construction industry has driven researchers to match natural resources with traditional technics to develop new building technologies. However, there are literature limitations about the correlation of fiber-matrix interface with the failure of natural fibers in mor
Cerâmica. Publicado em: 2022
-
17. Per-Aqueous Liquid Chromatography for the Separation of Polar Compounds Preparation and Characterization of Poly(ethylene oxide co dimethylsiloxane) Based Stationary Phase
Poly(ethylene oxide-co-dimethylsiloxane) was thermally immobilized on silica particles-Si(PEO)-to separate small polar compounds with water-rich mobile phases. Poly(ethylene oxide-co-dimethylsiloxane) content on Si(PEO) stationary phase was optimized using a central composite design. Infrared spectroscopy, scanning electron microscopy, and thermogravimetric
Journal of the Brazilian Chemical Society. Publicado em: 2022
-
18. Chemometric Evaluation of Poly(3-hexylthiophene) Electrochemical Aging Path as a Function of Electrochemical Synthesis Variables
Conductive polymers are versatile materials that can be applied in many different technology fields, especially green energy. They have several advantages, such as easy synthesis, low density, and cost. However, its electric conduction property is also related to material aging with great loss of their characteristics, limiting their applicability. The in-de
Journal of the Brazilian Chemical Society. Publicado em: 2022
-
19. A química analítica aplicada aos estudos de pigmentos rupestres: uma revisão
Instrumental advances have been employed in the study of archeological remains such as prehistoric rupestrians paintings with the objective of chemically characterizing them in order to reconstruct the cultural technologies of a prehistoric human group and/or to support conservation science studies. The analytical techniques most commonly used in archaeometr
Química Nova. Publicado em: 2022
-
20. Analysis and evaluation of structural properties of Co3O4 microparticles obtained at low temperature
Abstract In the present research, the synthesis of cobalt oxide Co3O4 was carried out using the sol-gel technique with subsequent heat treatment at 225 and 235 °C. The final product obtained was characterized by X-ray diffraction (XRD), showing a pure crystalline phase of Co3O4, cell parameters a=b=c=8.071 Å, and a volume of 525.7 Å3. The particle size wa
Cerâmica. Publicado em: 2022
-
21. Atomic Absorption Spectrometry as an Alternative to Determine the Presence of Gold Nanoparticles on or in Silica Matrix
Two different gold-silica-based nanomaterials were prepared: (i) silica-supported gold nanoparticles (AuNP/SiO2); and (ii) gold-silica core-shell nanoparticles (AuNP@SiO2). Three strategies for sample treatment (S), consisting in acid treatments, were employed: (S1) HNO3; (S2) HNO3 + HCl; and (S3) HF + HNO3 + HCl, applying microwave oven digestion for S2 and
Journal of the Brazilian Chemical Society. Publicado em: 2022
-
22. Simple and fast process using hydrochloric acid for producing synthetic zinc-rich stevensite
Abstract In the last decades, clays have been used in sectors such as health and cosmetics. This requires products that are increasingly pure and present homogeneous properties, hardly found in natural clays. The use of synthetic clays can be a solution. For this, it is necessary to explore techniques for their production. The main focus of this study was to
Cerâmica. Publicado em: 2022
-
23. The influence of separately and combined bentonite and kaolinite as binders for pelletization of NaA zeolite from coal fly ash
Abstract Pelletization of zeolitic materials is required to facilitate their practical industrial and commercial applications. Zeolite-NaA was synthesized from fly ash by the fusion method and shaped into spherical granules. Bentonite, kaolinite, and a combination of bentonite with kaolinite were tested as binders with different contents from 5 to 10 wt%. Th
Cerâmica. Publicado em: 2022
-
24. Obtainment of a new metal matrix composite from the recycling of UNS S31803 duplex stainless steel by powder metallurgy
Abstract The purpose of circular economy is to maximize resources efficiency. With the increase in consumption of raw materials, energy and waste generation, recycling is necessary for environmental and industrial reasons. Thus, the powder metallurgy, together with mechanical milling, stands as a new method for scraps recycling. This study aimed to produce U
REM - International Engineering Journal. Publicado em: 2022