Electrical Properties
Mostrando 13-24 de 835 artigos, teses e dissertações.
-
13. Investigation on Electrical Properties and Microdefects of Nb5+-Doped BaTiO3 Based Ceramics by Positron Annihilation Techniques
The influence of the Nb5+-doped content and the doping CaCO3 on the electrical properties and the microdefects of BSTN ceramics by Positron Annihilation Techniques were studied, which were fired at 1350 ºC for 2 hours in air. The PTCR characteristics in the BSTN samples were also investigated. Moreover, the information on microdefects in BSTN ceramics was d
Mat. Res.. Publicado em: 23/09/2019
-
14. Influence of Sintering Time on the PTCR Effect of Nb2O5-doped BaTiO3 Ceramics
The effects of the sintering time on the electrical properties and the positive temperature coefficient of resistance (PTCR) effect of Ba1.006(Ti1-xNbx)O3 (BTN) ceramics were investigated, which were sintered at 1190 ºC for 0.5-6 hours in a reducing atmosphere and then re-oxidized at 800 ºC for 1 hour. The results indicated that the sintering time affected
Mat. Res.. Publicado em: 16/09/2019
-
15. Uncured Polydimethylsiloxane as Binder Agent for Carbon Paste Electrodes: Application to the Quantification of Propranolol
This study describes the use of uncured polydimethylsiloxane (PDMS) as a binder agent to prepare carbon paste electrodes (CPEs). A comparative study between the properties of CPEs prepared with PDMS and mineral oil Nujol®, the most common binder agent for CPEs, was carried out. Cyclic voltammetry, electrochemical impedance spectroscopy, and chronoamperometr
J. Braz. Chem. Soc.. Publicado em: 16/09/2019
-
16. Nitretação por descargas elétricas da liga Ti-6Al-4V com adição de pó abrasivo SiC ao fluido dielétrico
RESUMO O processo de nitretação que usa Usinagem por Descargas Elétricas é um método que associa a capacidade de usinar superfícies complexas com a obtenção de tratamento termoquímico de nitretação. A fonte de nitrogênio é proveniente da uréia, que compõe o fluido dielétrico juntamente com água deionizada. A liga de titânio Ti-6Al-4V possui
Matéria (Rio J.). Publicado em: 16/09/2019
-
17. Improvement of Texture and Magnetic Properties in 4.5 wt.% Si Grain-Oriented Electrical Steels
4.5 wt.% Si grain-oriented electrical steel sheets were successfully produced by hot rolling, normalizing, warm rolling and annealing, and texture evolution was investigated using macro- and micro-texture analysis. It is found that the recrystallization texture of sheets is very sensitive to the warm rolling reduction, and 83-87% warm rolling reductions are
Mat. Res.. Publicado em: 19/08/2019
-
18. Equipamento Automatizado de Soldagem Capacitiva para Termopares
Resumo Os termopares são dispositivos elétricos de simples concepção utilizados na medição de temperatura, e possuem um grande uso na indústria. O termopar necessita de uma junção eficiente para os dois fios metálicos que o compõem, que comumente é feita pela soldagem. O processo de soldagem utilizado para construir um termopar pode ser feito de
Soldag. insp.. Publicado em: 15/08/2019
-
19. Modular modeling approach for FDM printed structures and piezo disks for metamaterial design
Abstract Research in metamaterials has recently gained interest in the field of noise and vibration control. The ability of creating band gap zones with minimum added mass is the main feature behind its success. In addition, the use of 3D printed parts, particularly the Fused Deposition Modeling (FDM), offers a practical solution for manufacturing parts with
Lat. Am. j. solids struct.. Publicado em: 12/08/2019
-
20. Influência do Regime Transiente Sobre a Microdureza e Microestrutura nos Aços ASTM-A36 e SAE-1045 Soldados pelo Processo MAG
Resumo O regime quase-estacionário pode não ser alcançado em soldagens a arco elétrico de peças de pequenas dimensões e/ou de materiais de maior condutividade térmica. Entretanto, o regime transiente sempre ocorrerá no início e no final da soldagem. Neste regime, a variação do fluxo de energia via calor pode promover variações microestruturais e
Soldag. insp.. Publicado em: 08/08/2019
-
21. Use of Firewood Ash Waste in Electrical Siliceous Porcelain
The use of firewood ash waste for the production of electric porcelain can represent an important technological and environmental alternative for the final disposal of this abundant solid waste material. This work aims to study the effect of replacing of sodium feldspar (albite) for firewood ash waste in electrical siliceous porcelain formulation. The firewo
Mat. Res.. Publicado em: 05/08/2019
-
22. Influence of Yttria-Stabilized Zirconia on Microstructure and Electrical Properties of Doped Lanthanum Gallate
Lanthanum gallate with partial substitutions for strontium and magnesium shows higher ionic conductivity than traditional ionic conductors such as yttria-stabilized zirconia (8YSZ), and has been considered for application as solid electrolyte and electrode in Solid Oxide Fuel Cells operating at intermediate temperatures (500-700ºC). Parallel to the developm
Mat. Res.. Publicado em: 01/08/2019
-
23. THERMOPHYSICAL PROPERTIES OF 1-ETHYL-3-METHYLIMIDAZOLIUM CHLORIDE SOLUTION FROM 293.15 TO 323.15 K
ABSTRACT Aqueous systems composed of ionic liquid make up a new alternative for use in processes involving the separation of biomolecules. The objective of this experiment was to obtain the thermo-physical properties of density, refractive index, electrical conductivity, molar volume, thermal expansion coefficient and apparent specific volume of the ionic li
Braz. J. Chem. Eng.. Publicado em: 15/07/2019
-
24. Study on mechanical & thermal properties of PCL blended graphene biocomposites
Abstract Graphene is a new carbon based nonmaterial that attracts the technology and constitutes one of the great promises for nanotechnology applications in a near feature. It’s having versatile intrinsic mechanical, thermal and electrical properties.By Incorporation of small amount of graphene fillers into polymer matrix can create attractive bio composi
Polímeros. Publicado em: 04/07/2019