Electrical Insulators
Mostrando 1-12 de 21 artigos, teses e dissertações.
-
1. Characterization of Algerian kaolins for utilization as a raw material in electrical insulators
Resumo O objetivo desta investigação foi caracterizar três amostras de caulim (DD1, DD2 e DD3) coletadas do depósito de Djebel Debbagh (leste da Argélia) para serem utilizadas em isoladores elétricos de porcelana. Análise granulométrica, fluorescência de raios X, difração de raios X, microscopia eletrônica de varredura e análise térmica (TG-ATD
Cerâmica. Publicado em: 06/06/2019
-
2. Changes in the crystalline degree in neutron irradiated EPDM viewed through infrared spectroscopy and inelastic neutron scattering
ABSTRACT The changes in the degree of crystallinity in commercial Ethylene Propylene Diene rubber-type M (EPDM) irradiated with neutrons at different doses has been studied by means of inelastic neutron scattering and infrared absorption spectroscopy experiments. EPDM samples were taken from the housing of non-ceramic electrical insulators which are used in
Matéria (Rio J.). Publicado em: 19/07/2018
-
3. Nanostructured Titanium Film Deposited by Pulsed Plasma Magnetron Sputtering (Pdms) on a High Voltage Ceramic Insulator for Outdoor Use
In this study, the cold plasma technique was used to produce nanometric titanium films with hydrophobic and anti-fouling properties. The films where deposited on porcelain electrical insulators surfaces to minimize the effects of leakage current. The magnetron sputtering technique was used with a target of pure titanium sheet, and argon as the ionization gas
Mat. Res.. Publicado em: 2015-08
-
4. Hydrophobicity Classification of Polymeric Insulators Based on Embedded Methods
Hydrophobicity is an important parameter to characterize electrical properties of insulated materials. Therefore, it is an urgent task to develop on-line instruments to identify the hydrophobicity of insulated material's surface conveniently, quickly and accurately. For this purpose, a novel evaluation system with image processing and decision tree is propos
Mat. Res.. Publicado em: 2015-02
-
5. Comparison of polymers and ceramics in new and discarded electrical insulators: reuse and recycling possibilities
The expansion and maintenance of electricity distribution networks generates large amounts of waste, much of it in the form of discarded insulators that are not reused or recycled. This paper describes the results of tests on used and new ceramic and polymeric insulators to verify if their exposure to weathering justifies their replacement. In new and used c
Matéria (Rio J.). Publicado em: 2013-12
-
6. Evaluation of the properties of iron oxide-filled castor oil polyurethane
The aim of this study was to obtain and evaluate the electrical, thermal and mechanical properties of iron oxide-filled castor oil polyurethane (PU/Fe2O3). The iron oxide used in this study was a residue derived from the steel pickling process of a Brazilian steel rolling industry. Polymeric composites with different iron oxide volume fractions (2.5, 5.0, 7.
Mat. Res.. Publicado em: 26/10/2012
-
7. Classification of polymers insulators hydrophobicity basead on digital image processing
Although the hydrophobicity is usually an arduous parameter to be determined in the field, it has been pointed out as a good option to monitor aging of polymeric outdoor insulators. Concerning this purpose, digital image processing of photos taken from wet insulators has been the main technique nowadays. However, important challenges on this technique still
Materials Research. Publicado em: 27/03/2012
-
8. Effect of artificial aging on polymeric surge arresters and polymer insulators for electricity distribution networks
A study was conducted to evaluate new and laboratory-aged samples of surge arresters and anchorage polymeric insulators, for 12 and 24 kV networks, which are used by the Rio Grande Energia (RGE). Power Utility Polymeric compounds were analyzed by Differential Scanning Calorimetry (DSC), Thermogravimetric Analysis (TG), Dynamic-Mechanic Analysis (DMA), Fourie
Polímeros. Publicado em: 13/12/2011
-
9. Obtenção de uma porcelana dielétrica a partir de matérias-primas do Rio Grande do Norte
The dielectric porcelain is usually obtained by mixing various raw materials proportions and is used in the production of electronic equipment for various applications, from capacitors of high and low Power to insulators for low, medium, high and extra high voltage, which are used in distribution lines and transmission of electricity.This work was directed t
Publicado em: 2010
-
10. Study of optical and electro-optical properties of diamond-like carbon films - DLC. / Estudo das propriedades ópticas e eletro-ópticas de filmes de carbono amorfo tipo diamante - DLC.
In this work it was studied electrical and optical characteristics of diamond-like carbon (DLC) films deposited in a reactive RF magnetron sputtering system on silicon and glass substrates. Samples were deposited at different process conditions in each type of substrate at two pressure conditions (5 mTorr and 10 mTorr) and four conditions of RF power (100 W,
Publicado em: 2010
-
11. Estudo do reaproveitamento de isoladores eletricos de porcelana como agregados em argamassas e concretos / Reutilization study of procelain elestric insulator as aggregates in mortars and concretes
Every construction material after sometime of using presents wastages which compromises its efficiency and turns indispensable its substitution or disposal. Porcelain electrical insulators, after a certain time of use, lose their insulator functions and are needed to be substituted and its monthly disposal in the brazilian electric sector comes to more than
Publicado em: 2009
-
12. Hydrophobicity classification in high voltage polymeric insulators / Classificação da hidrofobicidade em isoladores elétricos poliméricos de alta tensão
The aim of this study is to propose a new method to classify the hydrophobicity (HC) in high voltage polymer insulators. Currently the HC is based on the STRI guide (Swedish Transmission Research Institute) published in 1992, where the hydrophobicity is classified by contact angle and/or amount of wet surface. In the proposed method, the HC was analyzed by d
Publicado em: 2009