Distortional Buckling
Mostrando 1-9 de 9 artigos, teses e dissertações.
-
1. Finite strip method computer application for buckling analysis of thin-walled structures with arbitrary cross-sections
Abstract The Direct Strength Method (DSM) is a well-known formulation presented in the Brazilian standard ABNT NBR 14762:2010, that estimates the strength capacity of cold-formed steel (CFS) members. However, this formulation requires the elastic critical buckling loads as point of departure, regarding local (L), distortional (D) and global (G) modes, which
REM, Int. Eng. J.. Publicado em: 2021-09
-
2. Reliability assessment of cold-formed steel beams by the FORM method
Abstract This article presents a procedure for the reliability assessment of cold-formed steel beams based on the Direct Strength Method (DSM) and the Effective Section Method (ESM). Using a comprehensive database, a statistical analysis of the test results was performed to determine the statistical properties of the professional factor random variable. The
REM, Int. Eng. J.. Publicado em: 2021-06
-
3. Experimental analysis of built-up cold-formed steel lipped channel stub column
Abstract This article reports the results of experimental tests conducted on built-up cold-formed steel (CFS) stub columns, composed of double lipped channel members connected with self-drilling screws, which will be applied as the chord members of laced columns. These experiments aim to quantify the effect of four distinct web fastener layouts on the compos
REM, Int. Eng. J.. Publicado em: 16/09/2019
-
4. Distortional Failure and DSM Design of Cold-Formed Steel S-Shaped Beams Under Uniform Bending
Abstract This work reports a numerical investigation on the distortional buckling/post-buckling behaviors, ultimate strength and Direct Strength Method (DSM) design of cold-formed steel S-beams, commonly used in industrial rack systems. The analyzed beams are single-span, under uniform bending, exhibiting two different end support conditions and 5 cross-sect
Lat. Am. j. solids struct.. Publicado em: 2017-12
-
5. Effect of Web Holes and Bearing Stiffeners on Flexural-Shear Interaction Strength of Steel Cold-Formed C-Channel Sections
Abstract This paper presents an investigation on interaction equation between the required flexural strength, M, and the required shear strength, V, of cold-formed C-channels with web holes and bearing stiffeners. The primarily shear condition test was employed to study total 8 back to back lipped C channel sections of 95 and 100 mm depth when bearing stiffe
Lat. Am. j. solids struct.. Publicado em: 2016-06
-
6. Local/Distortional/Global buckling mode interaction on thin walled lipped channel columns
The buckling behaviour of pin ended cold-formed steel lipped channel columns affected by local / distortional / global buckling mode interaction under axial loading is simulated by using finite element software ABAQUS, and the results are compared with the test results available in the literature. The comparisons show that the proper analysis model can simul
Lat. Am. j. solids struct.. Publicado em: 2014-12
-
7. Numerical analysis of compressed cold formed steel members considering initial geometric imperfections / Análise numérica de perfis de aço formados a frio comprimidos considerando imperfeições geométricas iniciais
The work presents a numerical analysis on cold-formed steel members compressed between pinned ends. One is about an inquiry carried through in finite elements in which it was studied the influence of initial geometric imperfections, existing in plain channels and lipped channels, under the aspects of its form, magnitude and signal. The geometric imperfection
Publicado em: 2007
-
8. Theoretical and experimental analysis of cold-formed steel members under compression / Análise teórica e experimental de perfis de aço formados a frio submetidos à compressão
Cold-formed steel members present, in general, higher local slenderness than classical hot- rolled ones, which make them more prone to local buckling. Besides, thin-walled open sections have small torsional stiffness, and hence global torsional and flexural-torsional instability modes are many times more critical than global flexural ones. Also, distortional
Publicado em: 2006
-
9. Distortional buckling of cold-formed steel members under compression and bending. / Flambagem por distorção da seção transversal em perfis de aço formados a frio submetidos à compressão centrada e à flexão"
Os perfis de aço formados a frio apresentam, em geral, elevada relação largura/espessura, tornando-os suscetíveis à flambagem local, caracterizada por uma flambagem de chapa, mas que também pode ocasionar um outro modo de flambagem, denominado flambagem por distorção, desconsiderado no dimensionamento de perfis laminados, mas que pode resultar críti
Publicado em: 2003