Displacement Sensor
Mostrando 1-12 de 26 artigos, teses e dissertações.
-
1. Strain-deformation Reconstruction of Carbon Fiber Composite Laminates Based on BP Neural Network
The Carbon Fiber Reinforced Polymer (CFRP) laminate structural components used in the aerospace and military domains require high precision and strong stability. Usually the deformation of these structural components is difficult to be measured directly during operation, but the deformation of the CFRP laminate structure can be reconstructed with strain info
Mat. Res.. Publicado em: 14/11/2019
-
2. Square-Wave Voltammetry Determination of Ciprofloxacin in Pharmaceutical Formulations and Milk Using a Reduced Graphene Oxide Sensor
In this paper, a simple, sensitive and precise electroanalytical method was developed using a chemically-reduced graphene-oxide (CRGO)-modified glassy carbon electrode and square wave voltammetry (SWV) for determination of ciprofloxacin in pharmaceutical formulations (tablets) and milk samples. Advantages of this sensor include a potential displacement of 10
J. Braz. Chem. Soc.. Publicado em: 16/09/2019
-
3. Analysis of sensor placement in beams for crack identification
Abstract A previous study has shown that the mode shapes of a beam are more sensitive to damage than other vibrational parameters, thus making them better suited for crack identification purposes. However, they have the disadvantage of being more difficult to be measured. To overcome this difficulty, an interesting idea is to monitor changes produced by crac
Lat. Am. j. solids struct.. Publicado em: 29/10/2018
-
4. Estudio ab initio de propiedades electrónicas y estructurales de nanopartículas de SnO2 bajo presión
ABSTRACT Tin oxide (SnO2) has important applications, including as an elective material in the development of gas sensors. These devices improve their sensitivity and decrease their work temperature when the nanoparticle size is in the nanoscale order. Therefore, the gas sensor raises its efficiency noticeably. For this reason, the research of behavior at th
Matéria (Rio J.). Publicado em: 19/07/2018
-
5. On the Use of Special Functions for Analyzing the Steady State Creep in Short Fiber Composites Semi-theoretically
In this paper, a novel method is presented to obtain some unknowns such as displacement rate using special and well-behaved functions for short fiber composites in the steady state creep by semi-theoretical method (STM). The creep behaviors are predicted in the short fiber composites under tensile axial stress. Also, the regions under the partial debonding a
Mat. Res.. Publicado em: 2015-06
-
6. Sistemas de sensores ópticos baseados em fibra óptica de perfil-W dopada com Érbio / Optical sensing systems based on Erbium-doped W-fiber
Depressed-cladding (often referred to as dual-clad or "W"- fiber) fibers with fundamental-mode cutoffs provide high distributed losses at long wavelengths and low losses at short wavelengths. The magnitude of the abrupt transition between low-loss at short wavelengths and high-loss at long wavelengths exceeds 200 dB/km and is found to be extremely sensitive
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 30/07/2012
-
7. Active vibration control of a piezoelectric beam using PID controller: Experimental study
Vibration suppression of smart beams using the piezoelectric patch structure is presented in the present work. The smart system consists of a beam as the host structure and piezoceramic patches as the actuation and sensing elements. An experimental set-up has been developed to obtain the active vibration suppression of smart beam. The set-up consists of a sm
Lat. Am. j. solids struct.. Publicado em: 2012-12
-
8. Projeto e desenvolvimento de um sistema de medição sem contato aplicado ao processo de torneamento / DESIGN AND DEVELOPMENT OF A NON CONTACT MEASUREMENT SYSTEM APPLIED THE PROCESS OF TURNING
This work presents a non contact measurement techniques study on the manufacturing process and the design and development of a non contact measurement system for inspection of diameters of parts during the machining process on the lathe. Amongst the techniques are showed technologies which are based on physical principles of optical, pneumatic, electric or u
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 14/12/2011
-
9. Lightning risk warnings based on atmospheric electric field measurements in Brazil
Abstract: This paper presents a methodology that employs the electrostatic field variations caused by thundercloud formation or displacement to generate lightning warnings over a region of interest in Southeastern Brazil. These warnings can be used to prevent accidents during hazardous operations, such as the manufacturing, loading, and test of motor-rockets
J. Aerosp. Technol. Manag.. Publicado em: 2011-12
-
10. Contribution to drive the resonant linear compressor without displacement sensor / Contribuições para o acionamento do compressor linear ressonante sem sensor de posição
Nos compressores lineares ressonantes o pistão é acionado por um atuador linear e molas diretamente no sentido do seu movimento alternativo, formando um sistema massa-mola ressonante, eliminando assim os mancais mecânicos e o sistema biela e manivela dos compressores convencionais, reduzindo de forma significativa as perdas por atrito. A amplitude do desl
Publicado em: 2010
-
11. Os efeitos do nível de estabilização do desempenho na adaptação a perturbaçoes perceptivas imprevisíveis
The purpose this study was to investigate the effects of the levels of performance stabilization in the adaptation to unpredictable perceptive perturbations. Fifty one volunteers were randomly distributed in three groups: Control group (GC), Stabilization Group (GE) and Super Stabilization Group (GS). The experiment was conducted in two phases, named pre-exp
Publicado em: 2009
-
12. Food mechanics: a new device for testing fruits and vegetables
The new mechanical device developed is capable of performing compression tests but also bending, torsion and tensile tests. Its measurement system has the following components: a load cell (0 to 9800 N), a strain gauge signal conditioning board, a plug-in general purpose data acquisition board, and a displacement sensor (0 to 29.7 mm). These components are c
Journal of the Brazilian Society of Mechanical Sciences and Engineering. Publicado em: 2007-03