Direct Casting
Mostrando 1-12 de 26 artigos, teses e dissertações.
-
1. The Effect of Casting Speed and the Fraction of Al5%Ti1%B Inoculant on the Microstructure and Mechanical Properties of the AA5052 Aluminum Alloy Produced by the Direct Chill Process
This study aimed to assess the effect of casting speed and the addition of Al5%Ti1%B inoculant in the casted AA5052 aluminum alloy plate manufactured by the Direct Chill process. The focus of this work was to decrease the rejection index of rolled products due to the occurrence of superficial flaws on plates. These defects impact directly on the production c
Mat. Res.. Publicado em: 01/02/2018
-
2. Effect of casting mode and thermal treatments on the electrical conductivity of the AA4006 aluminum alloy
Abstract Initially studied was the effect of the casting mode on the electrical conductivity of AA4006 aluminum alloy sheets produced by both Twin Roll Casting (TRC) and by the semi-continuous Direct Chill (DC) industrial processes, when compared to sheets with commercial purity (AA1050) and high purity aluminum (AA1199). Then, the effects of heat treatments
REM, Int. Eng. J.. Publicado em: 2017-12
-
3. Cellular Ceramics Produced from Ceramic Shell: Processing and Characterization
In this work, ceramic shell (mullite source), an industrial solid waste from the lost-wax casting process, after crushing and milling steps, was used and evaluated as an alternative raw material source for the production of cellular ceramics for high temperature applications (> 1400 °C). The obtained ceramic shell powder, with particle size distribution (d5
Mat. Res.. Publicado em: 09/11/2017
-
4. Electrochromic Properties of Polyaniline-Based Hybrid Organic/Inorganic Materials
Hybrid materials based on polyaniline (PAni) were obtained by in situ polymerization of aniline with chitosan and/or organically modified clay (nanomer I-24) in HCl. The samples were characterized by Fourier transform infrared (FTIR) spectroscopy, X-ray diffraction (XRD), scanning electron microscopy (SEM) and direct current (DC) electrical conductivity. Thi
J. Braz. Chem. Soc.. Publicado em: 2016-10
-
5. Aqueous dispersion of red clay-based ceramic powder with the addition of starch
The optimum dispersion and rheological properties of red clay-based ceramic suspension loaded with unary and binary starch were investigated in aqueous medium. The aqueous ceramic suspension was prepared consisting of red clay, quartz, feldspar, and distilled water. Using a polyelectrolyte dispersant (Darvan 821A), the ternary ceramic powder was initially op
Mat. Res.. Publicado em: 22/01/2013
-
6. Does the casting mode influence microstructure, fracture and properties of different metal ceramic alloys?
The aim of the present study was to evaluate the tensile strength, elongation, microhardness, microstructure and fracture pattern of various metal ceramic alloys cast under different casting conditions. Two Ni-Cr alloys, Co-Cr and Pd-Ag were used. The casting conditions were as follows: electromagnetic induction under argon atmosphere, vacuum, using blowtorc
Brazilian Oral Research. Publicado em: 2012-06
-
7. Nanoparticle assisted coagulation of aqueous alumina suspensions
Colloidal processing of ceramics offers a high potential to achieve homogeneous microstructures with improved material properties. In this study, a novel forming method is investigated, which was already applied successfully for the fabrication of ceramic matrix composites (CMC), but is also considered to be a suitable direct casting technique for the fabric
Materials Research. Publicado em: 29/11/2011
-
8. Influence of starch type on characteristics of porous 3Y-ZrO2 prepared from a direct consolidation casting method
Starch consolidation casting has been successfully used to produce porous ceramics with complex shapes at a relatively low producing cost. In this work, porous 3Y-ZrO2 ceramics were produced using two types of starch (corn and potato). Concentrated (50-52 vol. (%)) aqueous suspensions of the different 3Y-ZrO2-starch mixtures (i.e. starch to zirconia weight r
Materials Research. Publicado em: 01/04/2011
-
9. Estudo comparativo da estampabilidade da liga de aluminio AA1050 partindo de placas obtidas por vazamento direto e bobinas obtidas por vazamento contínuo. / Comparative study of the deep drawing alloy AA1050 from plates obtained by direct casting and coils obtained by continuos casting.
Stampability of aluminum alloys is a subject of interest to several industrial sectors because they are largely used in the fabrication of several parts and components. The choice is based upon the stampability and the relative manufacturing capability in relation to other aluminum alloys that contain larger amounts of alloying elements and, consequently, hi
Publicado em: 2010
-
10. Influence of luting agents on time required for cast post removal by ultrasound: an in vitro study
OBJECTIVE: This in vitro study evaluated the influence of luting agents on ultrasonic vibration time for intraradicular cast post removal. MATERIAL AND METHODS: After endodontic treatment, 30 roots of extracted human canines were embedded in resin cylinders. The post-holes were prepared at 10 mm depth and their impressions were taken using autopolymerizing a
Journal of Applied Oral Science. Publicado em: 2009-06
-
11. Um estudo comparativo sobre a recristalização de chapas de alumínio AA1200 e AA3003 obtidas por lingotamento contínuo (twin roll caster) e por fundição de placas (direct chill). / A comparative recrystallization study of aluminium sheet AA1200 and AA3003 obtained by continuous casting (twin roll caster) and by casting of plates (direct chill).
A necessidade de redução de custos de produção torna o caster mais vantajoso que o processo de placas, porém a aplicação dos produtos obtidos via vazamento contínuo é limitada pelas condições microestruturais. A alta taxa de resfriamento no processo de vazamento, que pode ultrapassar 300 °C/s, resulta em uma condição de supersaturação dos ele
Publicado em: 2009
-
12. LOECK, Robson Becker. Comportamento eleitoral em Porto Alegre nas eleições de 2004: o voto nas regiões do Orçamento Participativo. 2008. 121f. Dissertação (Mestrado) Mestrado em Ciências Sociais. Universidade Federal de Pelotas, Pelotas. / LOECK, Robson Becker. Electoral behavior in Porto Alegre in the 2004 elections: ballots in the Participatory Budgeting Areas. 2008. 121f. Masters Thesis Masters Degree in Social Sciences. Federal University of Pelotas, Pelotas.
Participatory Budgeting, which was first introduced in the city of Porto Alegre in 1989, has enabled an increase in citizen participation in county government administration by means of a combination between direct and representative democracy. From then on, it has been acknowledged both nationally and internationally, turning into a model of an innovative e
Publicado em: 2008