Delamination
Mostrando 1-12 de 52 artigos, teses e dissertações.
-
1. Number of laminae on the mechanical behavior of glued laminated timber (glulam) of Toona ciliata produced with vegetable polyurethane adhesive
RESUMO A madeira laminada colada (MLC) é um material compósito obtido a partir da colagem de lâminas de madeira dispostas com as fibras paralelas entre si. O objetivo deste trabalho foi avaliar a influência do número de lâminas no comportamento mecânico de MLC de Toona ciliata produzidas com adesivo poliuretano de base vegetal. As vigas de MLC foram p
Ciênc. agrotec.. Publicado em: 20/12/2019
-
2. Avaliação dos processos de fratura em filmes finos através da simulação de ensaios de indentação com penetradores esféricos
RESUMO Recentes trabalhos propõem a utilização dos ensaios de indentação como uma ferramenta capaz de avaliar características mecânicas de filmes finos, assim como avaliar possíveis falhas em sistemas que conjugam filmes de alta dureza depositados em substratos metálicos em solicitações tribológicas. Entretanto, a implementação da técnica de i
Matéria (Rio J.). Publicado em: 25/11/2019
-
3. On Estimation of Adhesive Strength of Implants Bioactive Coating with Titanium by Density Functional Theory and Molecular Dynamics Simulations
One of the ways to improve and accelerate osseointegration of a surgical implant with bone is application of biocompatible coatings, in particular, hydroxyapatite (HAp). Since the cases of delamination of the coating take place in dental practice, it is very important to estimate the adhesive strength of HAp with the implant. A measure of the coating-to-subs
Mat. Res.. Publicado em: 30/05/2019
-
4. Investigating the Effect of Delamination Size, Stacking Sequences and Boundary Conditions on The Vibration Properties of Carbon Fiber Reinforced Polymer Composite
Abstract Composite structures are extensively used in various fields ranging from, but not limited to marine, aerospace, automotive, agricultural and industrial equipment due to their unique and excellent properties like weight associated with density. On an increase in their applications, it also requires special attention to manufacture and process the com
Mat. Res.. Publicado em: 07/01/2019
-
5. Finite Element Simulation of Interlaminar and Intralaminar Damage in Laminated Composite Plates Subjected to Impact
Abstract Here In this study, the composite laminates subjected to transverse impact with consideration interlaminar and intralaminar damage based on Cohesive Zone Model (CZM) and Progressive Damage Model (PDM) are investigated by numerical analysis using ABAQUS commercial finite element code. The delamination in stacking ply with the same fiber orientation
Lat. Am. j. solids struct.. Publicado em: 02/07/2018
-
6. Progressive failure prediction of pinned joint in quasi-isotropic laminates used in pipelines
Abstract To simulate the progressive failure of pinned joint in quasi-isotropic [0/45/-45/90]s glass fiber reinforced polymer (GFRP) composite laminates used in pipeline, 3-D finite element model is employed in the present work. Hashin failure criterion as a progressive damage model associated with Virtual-Crack-Closing-Technique (VCCT) delamination model h
Lat. Am. j. solids struct.. Publicado em: 02/07/2018
-
7. Mode I Interlaminar Fracture Toughness Analysis of Co-Bonded and Secondary Bonded Carbon Fiber Reinforced Composites Joints
Aiming to reduce aircraft weight, aeronautic industry seeks alternative materials and processes used to join its different structural parts. An option to traditional methods are high performance adhesive joints, which reduce weight, number of parts and component final cost, also resulting in higher strength structures. Although, the lack of experimental data
Mat. Res.. Publicado em: 05/02/2018
-
8. New Alternative to Produce Colored Polymer Nanocomposites: Organophilic Ni/Al and Co/Al Layered Double Hydroxide as Fillers into Low-Density Polyethylene
Green (Ni2+/Al+3) and pink (Co2+/Al+3) layered double hydroxides (LDH) (molar ratio of 3:1) were intercalated with several organic anions and used as functional colored fillers into low density polyethylene (LDPE) by melt mixing in amounts of 0.2 to 7 wt.%. Scanning electron microscopic (SEM) results of LDPE nanocomposites indicated that with low percentage
J. Braz. Chem. Soc.. Publicado em: 2017-12
-
9. A Recursive Methodology to Determine the Mechanical Response of Thin Laminated Plates in Bending
ABSTRACT: The paper's objective is to present the development of a recursive methodology which is based on Adomian Decompostion Method in order to evaluate the mechanical response of thin laminated plates in linear bending. By the equivalent layer concept, the linear relation between the equivalent stresses and the strains, namely ABD matrix, is established.
J. Aerosp. Technol. Manag.. Publicado em: 2017-12
-
10. The use of Shearography technique to evaluate polymeric composite repairs - case study
ABSTRACT Pipelines are subject to a variety of defects such as wall thickness loss, grooves, dents and holes. To restore the pipe integrity, polymeric composite repairs can be used. The inspection of repaired pipes is of fundamental importance, not only to verify the initial integrity, but also to monitor their state over time. Shearography is a laser optica
Matéria (Rio J.). Publicado em: 09/10/2017
-
11. Dental ceramics: a review of new materials and processing methods
Abstract The evolution of computerized systems for the production of dental restorations associated to the development of novel microstructures for ceramic materials has caused an important change in the clinical workflow for dentists and technicians, as well as in the treatment options offered to patients. New microstructures have also been developed by the
Braz. oral res.. Publicado em: 28/08/2017
-
12. Impact Damage Analysis with Stress Continuity Constraints Fulfilment at Damaged-Undamaged Regions and at Layer Interfaces
Abstract Low-velocity impacts have a relevant importance for safety of laminated and sandwich composite structures, because they are highly susceptible to damage. In this paper, a 3D cost effective zig-zag model is developed in order to efficiently simulate such impacts. It a priori fulfills the continuity of out-of-plane stresses at layer interfaces, the co
Lat. Am. j. solids struct.. Publicado em: 2017-08