Curing Temperature
Mostrando 13-24 de 99 artigos, teses e dissertações.
-
13. Efeito do envelhecimento acelerado sobre as propriedades de microconcreto reforçado com fibras longas de sisal
Resumo Neste trabalho dois microconcretos, com e sem metacaulinita, foram dosados para produção de compósitos laminados reforçados com fibras longas de sisal. Para garantir uma matriz livre de hidróxido de cálcio foi determinado o teor ideal de metacaolinita por análise termogravimétrica de pastas com teores de substituição de 20%, 30% e 40 nas ida
Ambient. constr.. Publicado em: 2019-03
-
14. Replacement of Commercial Silica by Rice Husk Ash in Epoxy Composites: A Comparative Analysis
Since epoxy resins are used as composite matrix with excellent results, and silica is one of the fillers most often employed, this study compared the performance of rice husk ash (RHA) as filler in epoxy composites, in replacement for high-purity silica. Composites were molded containing 20%, 40%, and 60% (wt) silica or RHA. Viscosity analysis, infrared spec
Mat. Res.. Publicado em: 05/04/2018
-
15. Toughening of polystyrene using styrene-butadiene rubber (SBRr) waste from the shoe industry
Abstract The vulcanized rubber waste from the shoe industry causes environmental damage when it is incinerated or inappropriately discarded, turning this into a problem of major concern. Therefore, this study had as the main objective the Polystyrene (PS) toughening using different contents of white vulcanized styrene-butadiene rubber (SBRr) waste produced i
REM, Int. Eng. J.. Publicado em: 2018-04
-
16. Multi-Objective Curing Cycle Optimization for Glass Fabric/Epoxy Composites Using Poisson Regression and Genetic Algorithm
In this study, a multi-parameter design of experiments, using Taguchi method, has been conducted in order to investigate the optimum curing conditions for glass fabric/epoxy laminated composites, followed by a statistical analysis and genetic algorithm optimization. Heating rate a, temperature T1 and duration h1 were treated as independent variables in a L25
Mat. Res.. Publicado em: 01/02/2018
-
17. Influence of tribological test on the global conversion of natural composites
Abstract The vinyl ester resins and natural composites have emerged as a suitable alternative in tribological application due to mechanical behavior, which relates to the conversion of the double bonds. During tribological test the permanent contact between polymeric sample and counterpart can increase the temperature affecting the crosslinking of the sample
Polímeros. Publicado em: 2017-12
-
18. Evaluation of Out-of-Autoclave (OOA) epoxy system
Abstract Epoxy resins (EP) usually cure in autoclave to minimize resin voids and to achieve the desired resin/fiber ratio. Cure parameters such as temperature, vacuum and pressure levels are controlled and monitored. Aiming time and cost optimization, new out-of-autoclave (OOA) cure processes have been developed lately. This study evaluated the cure cycle an
Polímeros. Publicado em: 2017-12
-
19. Evaluation of Filler Effects on the Dynamic Mechanical Behavior of HTPB-Elastomer Used as Binder in Exemplary Composite Formulations
ABSTRACT: This study aims to evaluate the dynamic mechanical properties of a binder, used in composite propellants, with increasing amount of different solid fillers. Dynamic Mechanical Analysis (DMA) is performed to determine the region of glass-rubber transition temperature (Tg). Further parameters were obtained from the description of the loss factor curv
J. Aerosp. Technol. Manag.. Publicado em: 2017-09
-
20. Physicochemical Characterization of Pulverized Phyllite Rock for Geopolymer Resin Synthesis
Geopolymeric materials have some unique properties such as early-high compressive strength, durability, resistance to acids and sulfates, ability to immobilize toxic and radioactive compounds, low porosity and high temperature resistance. These materials are strategic for sustainable development and are a suitable alternative to Portland cement. The use of p
Mat. Res.. Publicado em: 06/07/2017
-
21. Research on the Specific Heat Capacity of PBX Formulations Based on RDX
ABSTRACT The experimental results of specific heat capacity of 2 plastic bonded explosives formulations based on 1,3,5-trinitroperhydro-1,3,5-triazine, using differential scanning calorimetry thermal analysis, and the theoretical ones calculated with the specific heat capacity and mass fraction of individual compounds are compared for a temperature range bet
J. Aerosp. Technol. Manag.. Publicado em: 2016-09
-
22. Effect of new innovative restorative carbomised glass cement on intrapulpal temperature rise: an ex-vivo study
Abstract This study aimed to evaluate the temperature changes that occurred in the pulp chamber when using GCP Glass Carbomer Fill (GCP) and two different resin-modified glass-ionomer (RGI) restorative materials at different dentin thicknesses. A standardized Class I occlusal cavity with 1 mm or 2 mm dentin thickness was prepared in the extracted human molar
Braz. oral res.. Publicado em: 31/05/2016
-
23. The Effect of Composition, Temperature and Post-Irradiation Curing of Bulk Fill Resin Composites on Polymerization Efficiency
Abstract Objectives: To evaluate the polymerization efficiency of bulk fill resin-based composites (RBCs) and how their composition, temperature and post-irradiation polymerization influence the results. Methods and Materials: Eight bulk fill RBCs were investigated. Five specimens for each material were prepared for Vickers hardness measurements. The measu
Mat. Res.. Publicado em: 11/03/2016
-
24. Effect of Thermal Residual Stresses on Buckling and Post-Buckling Properties of Laminated Composites Perimetrally Reinforced
Abstract Several mechanical properties can be affected by the occurrence of residual stresses due to curing, and their effects are more pronounced in laminated composites. The effect of the thermal residual stresses on the buckling and post-buckling properties of perimetrally reinforced laminated composites is experimentally characterized. Carbon/epoxy lamin
Lat. Am. j. solids struct.. Publicado em: 2016-03