Contact Angle
Mostrando 1-12 de 293 artigos, teses e dissertações.
-
1. Morphology Behavior of Copper Films Deposited after Wet Surface Treatment on Polished Alumina
In this paper, a pre-treatment process for electroless copper (Cu) deposition on the polished alumina (Al2O3) 99.9% and the behavior of Cu plating by electroless process after Al2O3 surface treatment were explored. Our work was carried out by changing the roughness of Al2O3 through micro-etching (coarsening), nucleation its surface by a two-step method (sens
Journal of the Brazilian Chemical Society. Publicado em: 2022
-
2. Adhesion evaluation of the Rhodococcus opacus strain on an apatite surface
Abstract Adsorption of microorganisms and/or their different components onto a mineral surface would modify the surface characteristics of the mineral. Thus, this investigation evaluated the adsorption capacity of the Rhodococcus opacus strain onto an apatite surface. Zeta potential and contact angle measurements of the mineral showed dislocations of the val
REM, Int. Eng. J.. Publicado em: 2021-09
-
3. High-barrier and antibacterial films based on PET/SiOx for food packaging applications
Abstract High-barrier and antibacterial materials have potential applications in the field of preservative packaging for fresh meat products. In this paper, UV irradiation and silane coupling agent (KH550) were used to modify the surface of SiOx coating on polyester (PET)/SiOx film to prepare the PET/SiOx/chitosan and PET/SiOx/chitosan-nano-ZnO composite fil
Food Sci. Technol. Publicado em: 2021-09
-
4. EFECTO DE LA ADICIÓN DE POLÍMEROS DE CADENA CORTA SOBRE LA ESTRUCTURA QUÍMICA, PROPIEDADES MECÁNICAS, TÉRMICAS Y BIOLÓGICAS DE POLIURETANOS SINTETIZADOS CON DIISOCIANATOS ALIFÁTICOS Y ACEITE DE HIGUERILLA
The objective of this research was to synthesize biocompatible polyurethanes, with suitable mechanical properties to be used as biomaterials. Polyurethanes were synthesized with polyols derived from castor oil and isophorone diisocyanate (IPDI), hexamethylene diisocyanate and 4,4’-methylenebis (cyclohexyl isocyanate), with the addition of polycaprolactone/
Quím. Nova. Publicado em: 2021-01
-
5. MECHANICAL AND PHYSICAL PROPERTIES OF WOOD/POLYETHYLENE COMPOSITE REINFORCED WITH TIO2 NANOPARTICLES
ABSTRACT Wood plastic composite was fabricated using high density polyethylene and pine wood fiber. The effect of addition of TiO2 nanoparticles at different weight fractions (0%, 1%, 3%, and 5%) on some properties of the composite was examined. The experimental composites were tested for bending strength, tensile strength, Izod impact strength, thickness sw
CERNE. Publicado em: 2020-12
-
6. CONSTRUÇÃO DE UM SUPORTE AJUSTÁVEL LAB-MADE IMPRESSO EM 3D PARA MEDIÇÃO DE ÂNGULO DE CONTATO
Advances in the use of 3D printing technology have led to the development of new low-cost devices. This technology features high versatility, considering the easy modulation of the materials depending on its objectives and applications. In this sense, we have developed a laboratory-built contact angle measuring device (lab-made). The device was composed by t
Quím. Nova. Publicado em: 2020-09
-
7. INFLUENCE OF GLYPHOSATE CONCENTRATIONS ON SPRAY SOLUTION PHYSICOCHEMICAL CHARACTERISTICS AND DRIFT POTENTIAL
ABSTRACT The herbicide glyphosate is sprayed with varying application volumes that result in different concentrations used in the spray solutions. Thus, this study aimed to evaluate the effect of glyphosate concentrations on the potential risk of droplet drift, surface tension of spray solution, and contact angle of droplets on surfaces. Three experiments we
Eng. Agríc.. Publicado em: 2020-02
-
8. PMMA-SiO2 Organic-Inorganic Hybrid Coating Application to Ti-6Al-4V Alloy Prepared through the Sol-Gel Method
Siloxane-poly(methyl methacrylate) (PMMA) hybrid was synthesized based on the sol-gel method and applied to Ti-6Al-4V through dip-coating. The structural feature of the hybrid was subjected to Fourier-transform infrared spectroscopy (FTIR) and thermogravimetric analysis (TG); its morphological properties were analyzed through scanning electron microscope (SE
J. Braz. Chem. Soc.. Publicado em: 2020-02
-
9. Efeito da Adição de Propileno aos Gases de Proteção Convencionais na Soldagem GMAW Aplicada a Juntas de Topo e Ângulo
Resumo O presente trabalho teve por objetivo avaliar a adição de 1,3% de C3H6 ao CO2 puro e 0,6% de C3H6 à mistura de Ar+25%CO2, na soldagem de aço carbono utilizando o processo Gas Metal Arc Welding (GMAW) aplicado em juntas de topo com chanfro em V e ângulo em T. As soldas foram realizadas utilizando chapas de aço SAE 1020, arame de solda ER70S-6 de
Soldag. insp.. Publicado em: 02/12/2019
-
10. Plasma Treatment of Polyamide Fabric Surface by Hybrid Corona-Dielectric Barrier Discharge: Material Characterization and Dyeing/Washing Processes
In this study, the hybrid corona-dielectric barrier discharge plasma treatment was employed to modify the physical, chemical and morphological characteristics of a half-knitted fabric composed of 92% polyamide 6.6 and 8% elastane (PA). These properties of the fabric were evaluated by the water contact angle, x-ray diffraction, infrared spectroscopy, scanning
Mat. Res.. Publicado em: 28/11/2019
-
11. Surface morphology and repellency mechanism investigation of Salvinia molesta plant
ABSTRACT Bionics is a versatile tool with a technological potential, which designers use to search for signs and clues about functional elements and mechanisms in nature that allow for the development of products. The purpose of this study was to analyze the morphology of the aquatic plant Salvinia molesta, aiming to determine the water repellency of its lea
Matéria (Rio J.). Publicado em: 25/11/2019
-
12. Production of Carbon Foams from Rice Husk
The production of a material with rigid, multifunctional three-dimensional porous structure at a low cost is still challenging to date. In this work, a light and rigid carbon foam was prepared using rice husk as the basic element through a simple fermentation process followed by carbonization. For the fermentation process, the amount of biological yeast (7.5
Mat. Res.. Publicado em: 11/11/2019