Cold Formed Steel Sections
Mostrando 1-12 de 14 artigos, teses e dissertações.
-
1. Finite strip method computer application for buckling analysis of thin-walled structures with arbitrary cross-sections
Abstract The Direct Strength Method (DSM) is a well-known formulation presented in the Brazilian standard ABNT NBR 14762:2010, that estimates the strength capacity of cold-formed steel (CFS) members. However, this formulation requires the elastic critical buckling loads as point of departure, regarding local (L), distortional (D) and global (G) modes, which
REM, Int. Eng. J.. Publicado em: 2021-09
-
2. Structural Behaviour of Cold-Formed Steel of Double C-Lipped Channel Sections Integrated with Concrete Slabs as Composite Beams
Abstract Cold-formed steel (CFS) construction is widely recognised as an important contributor to sustainability and green construction. Thus, the use of CFS construction is encouraged and had been advanced by innovations in its structural applications. One such innovation that has recently gained popularity is the use of CFS sections in composite constructi
Lat. Am. j. solids struct.. Publicado em: 27/06/2019
-
3. Reliability analysis of welded and bolted connections in cold-formed steel sections
Abstract This article shows a study of the level of reliability of welded and bolted connections in cold formed steel members, for some limiting states, adopted by AISI and Brazilian codes. The aim of this study is the assessment of the reliability index β for a variation of the nominal live-to-dead load ratios as well as comparison of the value found consi
REM, Int. Eng. J.. Publicado em: 2018-07
-
4. Distortional Failure and DSM Design of Cold-Formed Steel S-Shaped Beams Under Uniform Bending
Abstract This work reports a numerical investigation on the distortional buckling/post-buckling behaviors, ultimate strength and Direct Strength Method (DSM) design of cold-formed steel S-beams, commonly used in industrial rack systems. The analyzed beams are single-span, under uniform bending, exhibiting two different end support conditions and 5 cross-sect
Lat. Am. j. solids struct.. Publicado em: 2017-12
-
5. Effect of Web Holes and Bearing Stiffeners on Flexural-Shear Interaction Strength of Steel Cold-Formed C-Channel Sections
Abstract This paper presents an investigation on interaction equation between the required flexural strength, M, and the required shear strength, V, of cold-formed C-channels with web holes and bearing stiffeners. The primarily shear condition test was employed to study total 8 back to back lipped C channel sections of 95 and 100 mm depth when bearing stiffe
Lat. Am. j. solids struct.. Publicado em: 2016-06
-
6. Local/Distortional/Global buckling mode interaction on thin walled lipped channel columns
The buckling behaviour of pin ended cold-formed steel lipped channel columns affected by local / distortional / global buckling mode interaction under axial loading is simulated by using finite element software ABAQUS, and the results are compared with the test results available in the literature. The comparisons show that the proper analysis model can simul
Lat. Am. j. solids struct.. Publicado em: 2014-12
-
7. Experimental investigation of the mechanical properties of ZAR-345 cold-formed steel at elevated temperatures
Considering the technical-scientific advances of recent years in the steel construction industry, there is a strong trend for the increasing use of cold-formed steel members in civil construction, due to several advantages such as cost and versatility of fabrication and erection. However, there is need for further study concerning the behavior of this type o
Mat. Res.. Publicado em: 01/08/2014
-
8. Study on the capacity of cold-formes steel built-up battened colums under axial compression
This paper presents the theoretical and numerical investigation results of the pin ended cold-formed steel built-up battened columns under axial compression. The finite element model was developed using the finite element software ABAQUS. The comparison of finite element analysis results match with the test results available in the literature shows that the
Lat. Am. j. solids struct.. Publicado em: 2014
-
9. Reliability-based evaluation of design guidelines for cold-formed steel-concrete composite beams
This paper presents an analysis of design guidelines for steel-concrete composite beams, formed by concrete-filled cold-formed steel sections. The study is based on experimental results for connector resistance (push-out) and for four full-scale beam bending tests. The accuracy of analytical design equations is evaluated by comparing their predictions with e
Journal of the Brazilian Society of Mechanical Sciences and Engineering. Publicado em: 2010-12
-
10. Processing of a duplex stainless steel by equal channel angular extrusion
A UNS S32205 duplex stainless steel was processed by ECAE in three different velocities, at room temperature, and heat treated in different temperatures and times to evaluate recrystallization. Attrition forces promoted great deformation heterogeneity in the samples sections, with hardness increase, and morphology changes in the grains and changing orientati
Matéria (Rio de Janeiro). Publicado em: 2010
-
11. Composite steel and concrete beam constituted by filled cold-formed steel section / Viga mista de aço e concreto constituída por perfil formado a frio preenchido
The composite steel and concrete beams have been largely applied in buildings and bridges constructions, having also a large amount of theoretical and experimental investigations about the use of hot-rolled and welded shapes and shear connectors that are compatible with these members, as for an example, the stud bolt and channel connectors. In the cold-forme
Publicado em: 2009
-
12. Comparative study of steel purlins in conventional beams, in planar trusses and multi-planar trusses / Estudo comparativo entre terças de aço, convencionais em vigas, em treliças planas e em treliças multiplanares
Steel roof systems are widely used in buildings that require large free internal spaces and small execution times, such as commercial and industrial warehouses and storage and distribution centers. The purlins have a considerable contribution in the roof system total weight composition. In this work was developed a study on the different types of purlins for
Publicado em: 2009