Cold Formed Steel Members
Mostrando 1-12 de 19 artigos, teses e dissertações.
-
1. Finite strip method computer application for buckling analysis of thin-walled structures with arbitrary cross-sections
Abstract The Direct Strength Method (DSM) is a well-known formulation presented in the Brazilian standard ABNT NBR 14762:2010, that estimates the strength capacity of cold-formed steel (CFS) members. However, this formulation requires the elastic critical buckling loads as point of departure, regarding local (L), distortional (D) and global (G) modes, which
REM, Int. Eng. J.. Publicado em: 2021-09
-
2. Reliability assessment of cold-formed steel beams by the FORM method
Abstract This article presents a procedure for the reliability assessment of cold-formed steel beams based on the Direct Strength Method (DSM) and the Effective Section Method (ESM). Using a comprehensive database, a statistical analysis of the test results was performed to determine the statistical properties of the professional factor random variable. The
REM, Int. Eng. J.. Publicado em: 2021-06
-
3. Experimental analysis of built-up cold-formed steel lipped channel stub column
Abstract This article reports the results of experimental tests conducted on built-up cold-formed steel (CFS) stub columns, composed of double lipped channel members connected with self-drilling screws, which will be applied as the chord members of laced columns. These experiments aim to quantify the effect of four distinct web fastener layouts on the compos
REM, Int. Eng. J.. Publicado em: 16/09/2019
-
4. Reliability analysis of welded and bolted connections in cold-formed steel sections
Abstract This article shows a study of the level of reliability of welded and bolted connections in cold formed steel members, for some limiting states, adopted by AISI and Brazilian codes. The aim of this study is the assessment of the reliability index β for a variation of the nominal live-to-dead load ratios as well as comparison of the value found consi
REM, Int. Eng. J.. Publicado em: 2018-07
-
5. Effect of Web Holes and Bearing Stiffeners on Flexural-Shear Interaction Strength of Steel Cold-Formed C-Channel Sections
Abstract This paper presents an investigation on interaction equation between the required flexural strength, M, and the required shear strength, V, of cold-formed C-channels with web holes and bearing stiffeners. The primarily shear condition test was employed to study total 8 back to back lipped C channel sections of 95 and 100 mm depth when bearing stiffe
Lat. Am. j. solids struct.. Publicado em: 2016-06
-
6. Experimental investigation of the mechanical properties of ZAR-345 cold-formed steel at elevated temperatures
Considering the technical-scientific advances of recent years in the steel construction industry, there is a strong trend for the increasing use of cold-formed steel members in civil construction, due to several advantages such as cost and versatility of fabrication and erection. However, there is need for further study concerning the behavior of this type o
Mat. Res.. Publicado em: 01/08/2014
-
7. Análise do comportamento a temperaturas elevadas de elementos de aço formados a frio comprimidos considerando restrição ao alongamento térmico / Analisys on the behaviour of cold formed steel columns under fire conditions with restarined thermal elongation
No presente trabalho se desenvolve como proposta principal, uma investigação experimental sobre o comportamento de elementos de aço formados a frio comprimidos em temperaturas elevadas considerando a influência da restrição ao alongamento térmico. Nessa investigação foram avaliadas as distribuições de temperaturas no contorno da seção transversa
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 26/10/2012
-
8. Theoretical and experimental analysis of cold-formed steel double angle members under compression / Análise teórica e experimental de barras em dupla cantoneira de aço formada a frio submetidas à compressão
Barras compostas em dupla cantoneira são constituídas por duas seções idênticas dispostas paralelamente, afastadas entre si e ligadas uma a outra apenas em alguns pontos ao longo do comprimento, por meio de chapas separadoras. O sistema aqui apresentado é bastante utilizado, principalmente em estruturas treliçadas leves, no entanto, não existem estud
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 24/08/2012
-
9. Comportamento estrutural e dimensionamento de cantoneiras de aço formadas a frio submetidas à compressão / Structural behavior and design of cold-formed steel angle columns
Envolto ao já conhecido comportamento de cantoneiras esbeltas de abas iguais, questões aparentemente contraditórias tem sido reportadas em estudos experimentais de diversos autores, entre elas a ocorrência de modos de instabilidade em desacordo com aqueles obtidos via análise de estabilidade elástica, e forças axiais resistentes muito diferentes dos r
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 27/04/2012
-
10. Análise de confiabilidade em ligações parafusadas em chapas finas e perfis de aço formados a frio / Reliability analysis in bolted connections in thin sheets and cold-formed steel members
Este trabalho apresenta uma investigação de modelos analíticos de previsão da força de tração resistente para ligações parafusadas em chapas finas e perfis de aço formados a frio, de acordo com quatro especificações de projeto (ABNT NBR 14762:2010, ANSI AISI S100:2007-S, AS/NZS 4600:2005 e EUROCODE 3 Parte1.3:2010). O estudo envolveu 404 resultad
Publicado em: 2011
-
11. Estudo da resistência a flambagem em perfis formados a frio / Study of buckling resistance of cold-formed steel members
A utilização dos perfis formados a frio vem aumentando de forma expressiva tanto na construção civil quanto na indústria mecânica. Com esse crescimento surge também uma necessidade de métodos de cálculo que auxiliem a avaliar corretamente seu desempenho estrutural. Nesse sentido, o presente trabalho propõe-se a fazer um estudo comparativo entre as
Publicado em: 2010
-
12. Composite steel and concrete beam constituted by filled cold-formed steel section / Viga mista de aço e concreto constituída por perfil formado a frio preenchido
The composite steel and concrete beams have been largely applied in buildings and bridges constructions, having also a large amount of theoretical and experimental investigations about the use of hot-rolled and welded shapes and shear connectors that are compatible with these members, as for an example, the stud bolt and channel connectors. In the cold-forme
Publicado em: 2009