Cnc Machining
Mostrando 1-12 de 23 artigos, teses e dissertações.
-
1. Analysis of Al2O3-ZrO2 ceramic insert in turning process of Ti-6Al-4V alloy using grey Taguchi-based response surface methodology (GT-RSM)
Abstract The present investigation aimed at a sustainable green turning operation of Ti-6Al-4V alloy using multi-objective optimization of surface roughness, tool flank wear, material removal rate, and tool wear loss with cutting speed, feed rate, and depth of cut as input parameters. The experiments were performed on a CNC lathe machine using an alumina-zir
Cerâmica. Publicado em: 2022
-
2. Towards Qualification of Friction Stir Welding to AA5083-O and AA5052-O Aluminum Alloys
Friction Stir Welding (FSW) is an excellent alternative for joining dissimilar and similar materials in comparison to conventional welding processes. In this sense, this work aims at qualifying FSW to similar AA5083-O and AA5052-O aluminum alloys, with 6.35 mm thickness, in a CNC machining center. Therefore, four welding experiments were undertaken. At first
Mat. Res.. Publicado em: 13/01/2020
-
3. Análise da rugosidade superficial de barras de aço SAE 1045 após torneamento
RESUMO Neste trabalho foram investigadas as influências de alguns dos principais fatores do torneamento sobre o acabamento da superfície e a rugosidade de uma peça torneada. Foram analisadas barras de aço SAE 1045 torneadas em um torno controle numérico computadorizado (CNC), com auxílio da técnica de Planejamento de experimentos (DOE) para formar tri
Matéria (Rio J.). Publicado em: 20/05/2019
-
4. Investigation of Austenitic Stainless Steel Coatings on Mild Steel Produced by Friction Surfacing Using a Conventional CNC Machining Center
The friction surfacing process allows deposition of similar and dissimilar coatings in the solid state, avoiding some of the problems associated with conventional coating methods in which fusion is involved. In the present work, a viability assessment of producing AISI 304 austenitic stainless steel coatings on AISI 1020 low-carbon steel substrates using a m
Mat. Res.. Publicado em: 21/01/2019
-
5. COMPARAÇÃO DE DESEMPENHO ENTRE PROGRAMAS CNC PARAMÉTRICOS E GERADOS POR SISTEMA CAM. / PERFORMANCE COPARISON BETWEEN PARAMETRIC PROGRAMS AND A CAM SYSTEM
A utilização de sistemas CAM para a geração de trajetórias de ferramenta em contornos de geometria simples depende diretamente do conhecimento e da capacidade do usuário na alimentação das informações e na utilização dos recursos disponíveis desses sistemas. A programação paramétrica exige uma base sólida no conhecimento da programação CN
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 15/12/2011
-
6. Contribuição para os usuários de sistemas CAD/CAM/CNC em operação de fresamento de topo em aço para moldes e matrizes / Contribution to the users of systems CAD/CAM/CNC in end milling operation in steel for molds and dies
The increased in the demand for plastic products and the need for reduction manufacturing times, and the growing dependence of man on the computer in present day, especially in manufacturing activities, has resulted in constant research of technological developments in order to supply these needs. In dies and molds manufacturing industry for plastic injectio
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 16/06/2011
-
7. Manufatura flexível: comparativo entre o modelo otimizado e o tradicional. / Flexible manufacture: comparative degree between the optimized model and the traditional one.
This work aims to optimize the machining process by reducing setup time and adjusting the consumption of cutting tools in a flexible manufacturing scenario, adopting an optimized model, which is then confronted with the traditional model, to show the advantages of one over the another. The tests consisted in making the turning operation of thinning on a CNC
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 01/03/2011
-
8. Surface integrity analysis when milling ultrafine-grained steels
This paper quantifies the effects of milling conditions on surface integrity of ultrafine-grained steels. Cutting speed, feed rate and depth of cut were related to microhardness and microstructure of the workpiece beneath machined surface. Low-carbon alloyed steel with 10.8 µm (as-received) and 1.7 µm (ultrafine) grain sizes were end milled using the down-
Materials Research. Publicado em: 13/12/2011
-
9. Influence of EP additive on tool wear in drilling of compacted graphite iron
Compacted Graphite Iron (CGI) is a good option for the manufacturing of engine blocks, because of the possibilities to decrease the wall thickness and to operate at higher pressures. However, due to its greater tensile strength and hardness compared with grey cast iron, the pearlitic CGI structure makes its machining more difficult. Thus, the aim of this pap
Journal of the Brazilian Society of Mechanical Sciences and Engineering. Publicado em: 2011-06
-
10. Tecnologia assistiva : personalização em massa através do design e fabricação de assentos customizados para cadeiras de rodas
The design of customized seats manufactured in polyurethane foams is and alternative to improve comfort and positioning for people with disabilities, as those people spend hours of the day seated in the same position. These support surfaces increase the contact area between the seat and user. This aspect improves weight distribution reducing localized pressu
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 2011
-
11. Effects of milling condition on the surface integrity of hot forged steel
This paper presents a study on the influence of milling condition on workpiece surface integrity focusing on hardness and roughness. The experimental work was carried out on a CNC machining center considering roughing and finishing operations. A 25 mm diameter endmill with two cemented carbide inserts coated with TiN layer were used for end milling operation
Journal of the Brazilian Society of Mechanical Sciences and Engineering. Publicado em: 2010-03
-
12. Contribuição ao estudo do processo de corte de ágata por jato d'água em formas complexas / Contribution to the study of development of complex forms agate products using water jet cutting process
No estado do Rio Grande do Sul, estão localizadas importantes regiões de extração e processamento do material gemológico ágata. Apesar da abundância de material, a maioria dos objetos produzidos apresenta baixo grau de inovação e tem, em co-mum, a utilização de processos que envolvam baixa tecnologia. A ágata é geralmente exportada em estado bru
Publicado em: 2010