Brittle Fracture
Mostrando 1-12 de 60 artigos, teses e dissertações.
-
1. PM versus IM Ti-5Al-5V-5Mo-3Cr Alloy in Mechanical Properties and Fracture Behaviour
The comparisons of mechanical properties and fracture behaviour between as-consolidated PM Ti-5553 alloy and as-cast IM Ti-5553 alloy were investigated through tensile, fracture toughness and impact toughness tests in this research. The slightly higher strength but much higher ductility and toughness can be identified in IM alloy specimens, which is also con
Mat. Res.. Publicado em: 27/06/2019
-
2. Effect of Extrusion and Heat Treatment on Microstructure and Mechanical Properties of Hypereutectic A390-0.3wt%Nd Alloy
An hypereutectic aluminium alloy with a composition of 16-18wt%Si, 4-5wt%Cu, 0.45-0.65wt%Mg, 0.3wt%Nd and Al balance (A390-0.3wt%Nd alloy) was processed by extrusion and aging at 200ºC for 10 hours. The effect of the thermomechanical processing and heat treatment on microstructure and mechanical properties was investigated for A390-0.3wt%Nd alloy. It was sh
Mat. Res.. Publicado em: 10/06/2019
-
3. Crystallization Behavior and Mechanical Properties of Cu-based Bulk Metallic Glass Composites
This work highlights the relationship between the preparation, crystallization behavior, microstructures, and mechanical properties of Cu-based bulk metallic glasses (BMGs) and their composites (BMGCs). (Cu47Zr45Al8)97.5Y1.5Nb in-situ BMGCs were prepared using isothermal annealing, and the experimental results indicate tunable mechanical properties of the al
Mat. Res.. Publicado em: 06/05/2019
-
4. Study of cracks in concrete target under deep penetration by a projectile
Abstract A large number of cracks occur in concrete structure after projectile penetration. The study of crack distribution and propagation process is the basis of damage assessment, structural repair and high dynamic fracture mechanism. In this paper, wire saw cutting, X-ray computed tomography (X-CT) and mechanical property testing of damaged concrete were
Lat. Am. j. solids struct.. Publicado em: 14/03/2019
-
5. Investigation of Stress Corrosion Cracking of Austenitic, Duplex and Super Duplex Stainless Steels under Drop Evaporation Test using Synthetic Seawater
Abstract Stress corrosion cracking (SCC) of UNS S31603 austenitic stainless steel (ASS), UNS S32205 duplex stainless steel (DSS) and UNS S32750 super duplex stainless steel (SDSS) was investigated. SCC tests were carried out at 110 ºC for 500 h under drops of synthetic seawater (DET, drop evaporation test). Two loading conditions were investigated: 50 % and
Mat. Res.. Publicado em: 31/01/2019
-
6. Microstructure and Properties of 3D Printed Inconel 718 Joint Brazed with BNi-2 Amorphous Filler Metal
Three dimensional (3D) printing technology has been widely used in metal manufacturing industry. This study focused on the vacuum brazing of 3D printed Inconel 718 superalloy with BNi-2 amorphous filler metal. Interfacial microstructure and element distribution revealed excellent wettability and spreadability of the filler metal as well as favorable brazabil
Mat. Res.. Publicado em: 14/11/2018
-
7. Nickel-Titanium Alloys Welding of Thin Sheets Using GTAW: Comparative Study Between Similar and Dissimilar Welding with AISI 304 Stainless Steel
The objective of the present work was to evaluate welding of thin sheets (thickness < 1 mm) of similar and dissimilar NiTi alloys with AISI 304 stainless steel using the Gas Tungsten Arc Welding (GTAW) process and to study the mechanical and metallurgical properties of the joints with and without post-welding heat treatment (PWHT). The GTAW process was chose
Mat. Res.. Publicado em: 08/11/2018
-
8. Lubricated Conditions Imposed on Coating Multi-layer on Wear Resistance Under Cr2O3 Effect
Lubricated pin-on-disk sliding wear tests were performed on applied to Al-0.1Mg-0.35Ni-Si Alloy by using the spray coating method has been investigated. Different loads were 5, 10, and 15 N at a sliding velocity, 1.32 m/s at room temperature and 60% relative humidity. The surfaces were analyzed by using X-ray diffraction the residual (XRD), energy dispersive
Mat. Res.. Publicado em: 16/04/2018
-
9. Finite element simulation of fracture in a restored premolar tooth using high aspect ratio elements
Abstract Introduction The term cracked tooth syndrome refers to an incomplete fracture of a vital posterior tooth that involves the dentin and occasionally extends into the pulp. There is a very limited number of publications trying to model dentin crack growth using numerical techniques. Therefore, it is essential to numerically model this phenomenon in o
Res. Biomed. Eng.. Publicado em: 19/03/2018
-
10. Mechanical and Metallurgical Characterization of Laser Welding on P91 Ferritic Steel and Incoloy 800HT Dissimilar Joints
In this work, microstructural characterization and mechanical properties of P91 and Incoloy 800HT dissimilar laser beam welded joint were analyzed. In addition to that, metallographical studies were conducted using Optical microscopy, Scanning electron microscopy (SEM) equipped with Energy-dispersive X-ray spectroscopy (EDX) and X-Ray diffraction analysis (
Mat. Res.. Publicado em: 01/02/2018
-
11. Electrochemical Noise for Detection of Stress Corrosion Cracking of Low Carbon Steel Exposed to Synthetic Soil Solution
In the last years, electrochemical noise (EN) has demonstrate that is capable of detect the initiation of cracks during the slow strain rate tests (SSRT). In this research, EN has been used as a tool to detect stress corrosion cracking (SCC) in low carbon steel (X52) exposed to a synthetic soil solution called NS4 at room temperature with pH of 5, 8 and 10.
Mat. Res.. Publicado em: 31/08/2017
-
12. Martensitic Transformation Under Compression of a Plasma Processed Polycrystalline Shape Memory CuAlNi Alloy
Shape memory alloys (SMA) are attracting considerable attention owing to possible applications from biomedical to aerospace. In particular, CuAlNi alloys present significant advantages associated with low cost, easy processing and superior thermo-electric conductivity over other SMAs such as the NiTi alloys. Characterization of some properties and structural
Mat. Res.. Publicado em: 31/08/2017