Bond Stress
Mostrando 1-12 de 105 artigos, teses e dissertações.
-
1. Interfacial Stress and Bond Strength of Bulk-Fill or Conventional Composite Resins to Dentin in Class II Restorations
Resumo O objetivo foi avaliar a resistência de união à microtração (RUμT) à dentina e o estresse interfacial em cavidades classe II restauradas com resina composta de incremento único ou convencional e as interfaces marginais. Cavidades classe II na face mesial, com margem gengival em dentina, foram confeccionadas em 72 terceiros molares, sendo divid
Braz. Dent. J.. Publicado em: 2020-09
-
2. Interfacial bond-slip relationship between Carbon Fiber Reinforced Polymer Plate and Concrete after High Temperature of Asphalt Paving Construction
Abstract The bond-slip relationship of Carbon Fiber Reinforced Polymer (CFRP) plate-concrete after the influence of high temperature action of Stone Mastic Asphalt (SMA) paving was investigated in this article. Two groups of double shear specimens with different bonding length were designed and tested. Based on the test results, the failure modes of specimen
Lat. Am. j. solids struct.. Publicado em: 25/11/2019
-
3. The use of a liner under different bulk-fill resin composites: 3D GAP formation analysis by x-ray microcomputed tomography
Abstract Gap formation of composite resin restorations is a serious shortcoming in clinical practice. Polymerization shrinkage stress exceeds the tooth-restoration bond strength, and it causes bacterial infiltration within gaps between cavity walls and the restorative material. Thus, an intermediate liner application with a low elastic modulus has been advis
J. Appl. Oral Sci.. Publicado em: 25/11/2019
-
4. An Anchorage System for Enhanced Bond Behavior between Carbon Fiber Reinforced Polymer Sheets and Cracked Concrete
Abstract The contribution of CFRP wraps, as an anchorage system, to enhancing bond behavior between CFRP sheet and cracked concrete, was investigated. Thirty six concrete blocks (150 x 150 x 200 mm) were cast with 3ϕ12 mm steel bars embedded laterally at different spacing along the 200-mm-dimension. Half of the moist-cured blocks were subjected to a cyclic
Lat. Am. j. solids struct.. Publicado em: 05/09/2019
-
5. Bond between steel and concrete made with ceramic waste aggregate
Abstract The reduction of natural resources combined with a substantial increase in the generation of solid waste in large urban centers, justifies the search for methods of reusing the construction industry waste. The ceramic industry has a high disposal rate during the manufacturing, transportation and eventual replacement of its products. In this case, re
REM, Int. Eng. J.. Publicado em: 2019-03
-
6. PARENTALIDADE DE PAIS DE RECÉM-NASCIDOS HOSPITALIZADOS POR SÍFILIS CONGÊNITA À LUZ DA TEORIA DAS TRANSIÇÕES
RESUMO Objetivo: compreender a vivência de transições na parentalidade de pais que tiveram um filho recém-nascido hospitalizado por sífilis congênita. Método: estudo qualitativo realizado com treze mães e quatro pais de recém-nascidos hospitalizados por sífilis congênita, no alojamento conjunto e unidade neonatal de um hospital universitário do
Texto contexto - enferm.. Publicado em: 31/01/2019
-
7. Manufacturing of Cu-Sn foams through SDP
ABSTRACT This work reports the processing of bronze foams manufactured by using the powder metallurgy method known as Sintering Dissolution Process. During the sintering step, a device with controlled atmosphere separated from the heating furnace was employed to avoid the quick oxidation of metal particles. The device allows to control its internal atmospher
Matéria (Rio J.). Publicado em: 19/07/2018
-
8. Effect on adhesion of a nanocapsules-loaded adhesive system
Abstract This study aimed to evaluate the in situ degree of conversion, contact angle, and immediate and long-term bond strengths of a commercial primer and an experimental adhesive containing indomethacin- and triclosan-loaded nanocapsules (NCs). The indomethacin- and triclosan-loaded NCs, which promote anti-inflammatory and antibacterial effects through co
Braz. oral res.. Publicado em: 01/02/2018
-
9. Pre-sintered Y-TZP sandblasting: effect on surface roughness, phase transformation, and Y-TZP/veneer bond strength
Abstract Sandblasting is a common method to try to improve the Y-TZP/veneer bond strength of dental prostheses, however, it may put stress on zirconia surfaces and could accelerate the t→m phase transformation. Y-TZP sandblasting before sintering could be an alternative to improve surface roughness and bonding strength of veneering ceramic. Objectives. Th
J. Appl. Oral Sci.. Publicado em: 2017-12
-
10. Rubbing time and bonding performance of one-step adhesives to primary enamel and dentin
Abstract Objectives: This study investigated whether increasing the concentration of acidic monomers in one-step adhesives would allow reducing their application time without interfering with the bonding ability to primary enamel and dentin. Material and methods: Experimental one-step self-etch adhesives were formulated with 5 wt% (AD5), 20 wt% (AD20), or
J. Appl. Oral Sci.. Publicado em: 2017-10
-
11. Polymerization shrinkage stress of composite resins and resin cements – What do we need to know?
Abstract Polymerization shrinkage stress of resin-based materials have been related to several unwanted clinical consequences, such as enamel crack propagation, cusp deflection, marginal and internal gaps, and decreased bond strength. Despite the absence of strong evidence relating polymerization shrinkage to secondary caries or fracture of posterior teeth,
Braz. oral res.. Publicado em: 28/08/2017
-
12. Finite Element Analysis of Reinforced Concrete Beam-Column Connections with Governing Joint Shear Failure Mode
Abstract Reinforced concrete (RC) beam-column connections especially those without transverse reinforcement in joint region can exhibit brittle behavior when intensive damage is concentrated in the joint region during an earthquake event. Brittle behavior in the joint region can compromise the ductile design philosophy and the expected overall performance of
Lat. Am. j. solids struct.. Publicado em: 2017-08