Solvent Degradation and Polymerization Shrinkage Reduction of Resin Composites Using Isobornyl Methacrylate

AUTOR(ES)
FONTE

Braz. Dent. J.

DATA DE PUBLICAÇÃO

03/06/2019

RESUMO

Resumo O objetivo nesse estudo foi utilizar o isobornil metacrilato (IBOMA) como monômero combinante ou substituinte na matriz resinosa de resinas compostas odontológicas. Para tanto, a matriz resinosa foi formulada com 60 % em peso de BisGMA e 40 % em peso de monômero diluente. O TEGDMA foi utilizado como único monômero diluente para o grupo controle com 40 % em peso, enquanto a substituição total de TEGDMA foi feita com 40 % em peso de IBOMA. Na combinação de IBOMA e TEGDMA foram utilizados 20 % em peso de cada monômero. Na matriz resinosa, 65 % em peso de partículas de carga foi adicionado. O grau de conversão (GC) utilizando FT-IR, a resistência flexural (RF), o módulo flexural (MF), a contração de polimerização por formação de gap (FG) utilizando Microscopia Confocal à Laser, a Dureza Knoop (DK) e a degradação em solvente (DS) foram avaliados. Todos os dados foram analisados utilizando ANOVA e teste de Tukey (α=0.05; b=0.2). Os resultados demonstraram que reduzindo ou substituindo o TEGDMA utilizando o IBOMA não afetou o GC (p=0.085), a RF (p=0.886) ou o MF (p=0.414). Ainda, quando o IBOMA foi utilizado como um monômero combinante ou substituinte, menor FG foi observada em comparação ao controle contendo apenas TEGDMA como monômero diluente (p=0.032). Contudo, apesar de todos os compósitos terem apresentados redução na DK durante o teste de DS, a combinação de IBOMA e TEGDMA demonstrou uma redução na DK similar ao grupo (p=0.001), enquanto a substituição total de TEGDMA com IBOMA reduziu a DK após DS (p=0.041). Dessa forma, a combinação do IBOMA e TEGDMA parece reduzir DS e a FG sem afetar as propriedades de resinas compostas.Abstract The aim of this study was to use the isobornyl methacrylate (IBOMA) as a combining or substituent diluent monomer in the resin matrix of dental resin composites. Thus, the resin matrix was formulated with 60 wt% of BisGMA and 40 wt% of diluent monomers. TEGDMA as the only diluent monomer was used as control with 40 wt%, while total substitution of TEGDMA was done with 40 wt% of IBOMA. The combination of IBOMA and TEGDMA was done with 20 wt% of each monomer. To the resin matrix, 65 wt% of filler particles was added. Degree of conversion (DC) using FT-IR, flexural strength (FS), flexural modulus (FM), polymerization shrinkage by gap formation (GF), Knoop hardness (KH) and solvent degradation (SD) were evaluated. Data were analyzed using ANOVA and Tukey’s test (α=0.05; b=0.2). The results showed that reducing or substituting TEGDMA using IBOMA did not affect the DC (0.085), FS (p=0.886) or FM (p=0.414). Also, when IBOMA was used, lower GF was found in comparison to the control containing only TEGDMA as the diluent monomer (p=0.032). However, even though all composites presented reduction in KH during the SD test, the combination of IBOMA and TEGDMA showed similar reduction in KHN in comparison to the control group (p=0.001), while the total substitution of TEGDMA with IBOMA decreased KHN after SD (p=0.041). Thus, the combination of IBOMA and TEGDMA seem to reduce SD and GF without affecting the properties of resin composites.

Documentos Relacionados