Aluminum Oxide
Mostrando 13-24 de 152 artigos, teses e dissertações.
-
13. Bond strength between a polymer-infiltrated ceramic network and a composite for repair: effect of several ceramic surface treatments
Abstract: The effects of several ceramic surface treatments on bond strength of a polymer-infiltrated ceramic network and resin composite as repair material were evaluated. CAD-CAM blocks of a polymer-infiltrated ceramic network (Vita Enamic) were sliced and subjected to aging process, followed by embedding in acrylic resin. The bonding/repair area was treat
Braz. oral res.. Publicado em: 05/04/2018
-
14. Effectiveness of Arsenic Co-Precipitation with Fe-Al Hydroxides for Treatment of Contaminated Water
ABSTRACT Wastewater treatment is a challenging problem faced by the mining industry, especially when mine effluents include acid mine drainage with elevated arsenic levels. Iron (hydr)oxides are known to be effective in removal of As from wastewater, and although the resulting compounds are relatively unstable, the presence of structural Al enhances their st
Rev. Bras. Ciênc. Solo. Publicado em: 29/03/2018
-
15. Theoretical Approach to Simulate Efficient Selective Solar Absorbers With Micro or Nano Structured Arrays
Study of the solar absorber with photonic crystal or micro structures as the heat absorbing surfaces operated at a high-temperature was conducted. Numerical calculations based on rigorous coupled-wave analysis were performed to determine the absorptance of the photonic crystal surface on the absorber. The effect of nano geometry of the photonic crystal in tu
Mat. Res.. Publicado em: 22/03/2018
-
16. Use of SnOx:F in the Recycling of Silicon Solar Cells
Amongst the many parts of a silicon cells photovoltaic module, silicon is the most important and expensive constituent. Thus, research on silicon recycling from damaged cells can lead to economic and environmental benefits. In this work, the broken silicon cells were tailored to function along with the fluorine-doped tin oxide as the transparent electric con
Mat. Res.. Publicado em: 22/01/2018
-
17. Application viability evaluation of the Minimum Quantity Lubrication coolant technique under different flow rates in Plunge Cylindrical Grinding of the ABNT 4340 steel with aluminum oxide wheel
Abstract The coolant delivery technique known as Minimal Quantity Lubrication (MQL) has been employed in machining since the end of the 20th Century and has gained considerable evidence in the last years as a viable alternative to the use of the conventional coolant technique (flood). Due to the low oil flow rate delivered by the MQL technique in grinding op
REM, Int. Eng. J.. Publicado em: 2017-12
-
18. Pre-sintered Y-TZP sandblasting: effect on surface roughness, phase transformation, and Y-TZP/veneer bond strength
Abstract Sandblasting is a common method to try to improve the Y-TZP/veneer bond strength of dental prostheses, however, it may put stress on zirconia surfaces and could accelerate the t→m phase transformation. Y-TZP sandblasting before sintering could be an alternative to improve surface roughness and bonding strength of veneering ceramic. Objectives. Th
J. Appl. Oral Sci.. Publicado em: 2017-12
-
19. Dentin pretreatment and adhesive temperature as affecting factors on bond strength of a universal adhesive system
Abstract Objectives: To evaluate the effects of dentin pretreatment and temperature on the bond strength of a universal adhesive system to dentin. Material and Methods: Ninety-six extracted non-carious human third molars were randomly divided into 12 groups (n=8) according to Scotchbond Universal Adhesive (SbU) applied in self-etch (SE) and etch-and-rinse
J. Appl. Oral Sci.. Publicado em: 2017-10
-
20. A Model for the Formation of Niobium Structures by anodization
The fluoride use for anodizing electrolytes has been primarily responsible for the formation of nanoporous oxides at valve metals, except aluminum, since it causes a dissolution process. This study presents the formation of an oxide model according to the following anodizing parameters: 100 V, 12.73 mA/cm2, room temperature and the niobium samples anodized i
Mat. Res.. Publicado em: 25/05/2017
-
21. Evaluation of nickel and copper catalysts in biogas reforming for hydrogen production in SOFC
ABSTRACT The solid oxide fuel cells (SOFC) enable the efficient generation of clean energy, fitting the current requirements of the growing demand for electricity and for the environment preservation. When powered with biogas (from digesters of municipal wastes), the SOFCs also contribute to reduce the environmental impact of these wastes. The most suitable
Matéria (Rio J.). Publicado em: 22/05/2017
-
22. Preparation and Anti-Corrosive Properties of Cerium Oxide Conversion Coatings on Steel X52
In this study, cerium-based conversion coating was deposited on steel X52 by dip immersion method. Cerium oxide/hydroxide is an environmentally friendly conversion coating. The effects of immersion times and immersion temperatures on corrosion properties of cerium conversion coating on steel X52 were studied. Its corrosion resistance in 3.5 wt.% NaCl solutio
Mat. Res.. Publicado em: 09/02/2017
-
23. One-year aging effects on microtensile bond strengths of composite and repairs with different surface treatments
Abstract The present study aimed to evaluate effects of different surface treatments and aging of composite cylinders on bond strength of composite resin repair. Thirty-two composite cylinders were produced and divided into four groups according to type of surface treatment and storage time of composite cylinder and repair. Cylinder surface of control group
Braz. oral res.. Publicado em: 05/01/2017
-
24. Anomalous Behavior of a Solid Rocket Motor Nozzle Insert During Static Firing Test
ABSTRACT This paper presents the study and development of a firing test used to evaluate the behavior of a solid rocket motor. The motivation for the development of a subscale solid rocket motor with end burning propellant grain geometry arose from the need to evaluate the nozzle inserts of graphite for the possible replacement with the carbon fiber-reinforc
J. Aerosp. Technol. Manag.. Publicado em: 2016-12