Alternative Alloys
Mostrando 1-12 de 28 artigos, teses e dissertações.
-
1. Towards Qualification of Friction Stir Welding to AA5083-O and AA5052-O Aluminum Alloys
Friction Stir Welding (FSW) is an excellent alternative for joining dissimilar and similar materials in comparison to conventional welding processes. In this sense, this work aims at qualifying FSW to similar AA5083-O and AA5052-O aluminum alloys, with 6.35 mm thickness, in a CNC machining center. Therefore, four welding experiments were undertaken. At first
Mat. Res.. Publicado em: 13/01/2020
-
2. Study of the metallurgical bond between 316 steel substrates and NiCrAlY coating sprayed by HVOF and irradiated with a low power CO2 laser
RESUMO Considerando a importância do desenvolvimento de novos materiais ao longo dos últimos anos; os pesquisadores vêm estudando soluções eficazes através do uso de revestimentos de alta dureza para aplicação em ferramentas de corte e matrizes de conformação. Revestimentos de carboneto de tungstênio (WC) são um dos mais utilizados em sistemas de
Matéria (Rio J.). Publicado em: 16/09/2019
-
3. Estudo de recobrimentos de silicato e aluminato obtidos por oxidação por plasma eletrolítico em liga de alumínio
RESUMO As ligas de Alumínio são utilizadas para diversas finalidades e para a maioria dos casos a superfície desses materiais precisa ser modificada a fim de se melhorar propriedades como resistência ao desgaste e corrosão. Neste cenário, o processo de oxidação por plasma eletrolítico (PEO) surge como uma alternativa viável para produção de recob
Matéria (Rio J.). Publicado em: 20/05/2019
-
4. Medición del módulo de Young en metales mediante la técnica de excitación por impulso
ABSTRACT The impulse excitation, as non-destructive technique, allows to determine the elastic constants of materials by means of measurement of natural frequency of vibration of bars in different modes, excited by an impact in a point. In this work, the Young’s modulus of copper, aluminum and copper-based alloys samples was determined. The measurements we
Matéria (Rio J.). Publicado em: 19/07/2018
-
5. A new technique in the excavation of ground-nest bee burrows (Hymenoptera: Apoidea)
ABSTRACT Bees have a diversified natural history, thus the methods applied to study such diversity are varied. When it comes to studies of nesting biology, bees which nest in pre-existing cavities have been reasonably well studied since researchers started using trap-nests. However, bees whose nests are built underground are poorly studied due to the difficu
Rev. Bras. entomol.. Publicado em: 2018-01
-
6. Microstructure and Mechanical Properties of Ti-12Mo-8Nb Alloy Hot Swaged and Treated for Orthopedic Applications
Metastable β-type Ti alloys with non-toxic addition elements such as Mo, Zr, Sn, Ta and Nb were developed as an alternative to the widely used Ti-6Al-4V alloy for biomedical applications. These alloys possess enhanced biocompatibility and reduced elastic modulus in comparison with Ti-6Al-4V. Moreover, for orthopedic implants, low Young's modulus is required
Mat. Res.. Publicado em: 09/11/2017
-
7. Development of a Material for Manufacturing a Mold for Plastic Injection
Injection molding is a process used to manufacture high volumes of plastic containers of complex geometric shapes. Although CuBe has always been used, there are currently some alternative alloys such as the CuNiSiCr alloy that has lower manufacturing cost and similar properties. The objective of this paper is to characterize, by techniques of microscopy, the
Mat. Res.. Publicado em: 07/08/2017
-
8. Fibroblast and pre-osteoblast cell adhesive behavior on titanium alloy coated with diamond film
It is well known that titanium alloys have mechanical strengths comparable to steels, as well as high corrosion resistance. Also, they have the advantage of promoting osseointegration, when used in medical and dental implants. This work aims to describe the adhesion properties of fibroblast and osteoblast cells on the surface of titanium aluminum vanadium al
Mat. Res.. Publicado em: 03/08/2017
-
9. Analysis of precipitate density of an aluminium alloy by TEM and AFM
Abstract The quantification of nanometric precipitates in Al-Zn-Mg-Cu alloys has been performed by a series of experimental techniques. Especially in the AA7050 alloy, after ageing heat treatment, the particles responsible for the hardening become very thin. Typically, these precipitates of nanometric sizes are mainly characterized by transmission electron m
REM, Int. Eng. J.. Publicado em: 2016-12
-
10. Action of Antimicrobial Copper on Bacteria and Fungi Isolated from Commercial Poultry Hatcheries
ABSTRACT Since 2008, when the US Environmental Protection Agency (EPA) registered copper and its alloys as an antimicrobial agent for contact surfaces, research has demonstrated their antimicrobial activity. The aim of this study was to evaluate the efficacy of antimicrobial copper against bacteria and fungi isolated from commercial poultry hatcheries in ord
Rev. Bras. Cienc. Avic.. Publicado em: 2016-12
-
11. Properties and Performance of Ultrafine Grained Titanium for Biomedical Applications
The use of materials for biomedical applications has become vital to enhance the quality of life and longevity of human beings. Commercially pure titanium (cpTi) and titanium alloys are the most adequate materials for some biomedical applications, but cpTi and the Ti-6Al-4V alloy (Ti G5) have limitations for biomedical application due to low mechanical stren
Mat. Res.. Publicado em: 03/11/2015
-
12. The use of single point incremental forming for customized implants of unicondylar knee arthroplasty: a review
Abstract Introduction The implantable devices are having enormous market. These products are basically made by traditional manufacturing process, but for the custom-made implants Incremental Sheet Forming is a paramount alternative. Single Point Incremental Forming (SPIF) is a manufacturing process to form intricate, asymmetrical components. It forms the co
Res. Biomed. Eng.. Publicado em: 30/10/2015