Aisi H13 Steel
Mostrando 1-12 de 16 artigos, teses e dissertações.
-
1. EXTRATO DE HIBISCO-COLIBRI COMO INIBIDOR VERDE DE CORROSÃO DO AÇO-CARBONO EM ÁCIDO SULFÚRICO
For this work, a hydroalcoholic extract was prepared from the aerial parts of the Malvaviscus arboreus (Malvaceae) species, popularly known as hibisco-colibri in Brazil; and then, investigated by infrared and NMR spectroscopy. A class of special metabolites containing a porphyrin skeleton and pyrrole units was determined by typical absorption spectra, mainly
Quím. Nova. Publicado em: 26/08/2019
-
2. Effect of Processing Route on the Microstructure and Mechanical Properties of Hot Work Tool Steel
Powder metallurgy is a growing sector in industrial production, as it offers outstanding energy, cost and material savings in comparison with established processing routes such as casting. Hot work toll steels are usually produced by ingot metallurgy, but also by powder metallurgy, namely hot isostatic pressing and powder forging routes. In this paper we inv
Mat. Res.. Publicado em: 21/08/2017
-
3. Micro-Scale Abrasive Wear Testing of CrN Duplex PVD Coating on Pre-Nitrided Tool Steel
Specific wear rates were calculated from a series of micro-scale abrasive tests by means of the calotte-grinding method. The tested material was a CrN coating deposited by arc evaporation on ion-nitrided AISI H13 steel. Characterizations included: phase analysis, chemical composition, metallography, microhardness, micro-scratch resistance and nano-indentatio
Mat. Res.. Publicado em: 22/06/2017
-
4. Estudo do comportamento tribológico do aço AISI H13 submetido a tratamento termoquímico de boretação / Study of tribological behavior of AISI H13 steel subjected to boriding thermochemical treatment
In this work, solid boriding thermochemical treatment was carried out using Ekabor 1-V2 and one blend as boriding agents and heat treatment of quenching and tempering of AISI H13 tool steel in order to compare and evaluate the tribological behavior and the properties acquired for four studied conditions, that were: Ekabor powder boriding, Ekabor powder borid
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 18/06/2012
-
5. Influence of the microstructure on the electrochemical properties of Al-Cr-N coatings deposited by co-sputtering method from a Cr-Al binary target
In the present paper, aluminum chromium nitride (Al-Cr-N) films were deposited onto AISI H13 steel substrates by a reactive d.c magnetron co-sputtering system in an atmosphere of Ar/N2 (90/10) gas mixture from a binary target composed of chromium (99.95%) and aluminum (99.99%). Different powers (40, 50, 60, and 70 W) were applied to the target, in order to s
Mat. Res.. Publicado em: 04/12/2012
-
6. Estudo da integridade superficial e seu efeito na fadiga de contato de um aço ferramenta. / The effect of surface integrity on the contact fatigue resistance of a tool steel.
Os processos de manufatura, bem como os parâmetros de processamento utilizados produzem diferentes resultados com relação à integridade de uma superfície. Estas alterações se refletem em mudança das propriedades da superfície, as quais podem influenciar o desempenho dos componentes. O presente trabalho estuda o efeito da integridade superficial gera
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 19/09/2011
-
7. Estudo da influência do tratamento criogênico no aço AISI H13 / Study of the influence of cryogenic treatment in AISI H13 steels
Há alguns anos, diversos estudos da influência dos parâmetros do tratamento térmico vêm sendo desenvolvidos, para a obtenção de propriedades que permitam atingir os requisitos de trabalho e que gerem ferramentas de vida útil estendida. Nesse contexto, tem sido demonstrado que o tratamento criogênico não só provoca a transformação da austenita re
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 21/02/2011
-
8. Wear evaluation of WC inserts coated with TiN/TiAlN multinanolayers
TiN/TiAlN multilayers were deposited by radio frequency, r.f., reactive magnetron sputtering by using titanium and aluminum targets with 10 cm diameter and 99.99% purity in an argon/nitrogen atmosphere, applying a substrate temperature of 300 ºC. WC inserts were used as substrates to improve the mechanical and tribological properties of TiN/TiAlN multilayer
Journal of the Brazilian Society of Mechanical Sciences and Engineering. Publicado em: 2010-06
-
9. High temperature oxidation behavior of the AISI 430A and AISI 430E stainless steels in Ar/H2/H2O atmosphere
The high temperature oxidation behavior of two ferritic stainless steels type AISI 430A and AISI 430E is examined at low oxygen pressure and high temperatures. The AISI 430A steel is ferritic up to 860 °C. Above this temperature, this steel is bi-phased: presence of austenite and ferrite phases. The 430E steel is stabilized with Nb, and is ferritic at all t
Materials Research. Publicado em: 2008-06
-
10. Estudo da obtenção e das propriedades dos filmes de TiN e TiC depositados sobre aços ferramentas AISI H13 e D2 nitretados e não nitretados. / Study of the making and properties TiC and TiN coatings deposited on AISI H13 and AISI D2 toll nitrated and not nitrated steel.
Filmes de nitreto de titânio e carbeto de titânio foram obtidos por deposição reativa via magnetron sputtering, utilizando como gases reativos, nitrogênio e metano, respectivamente. Foram depositados filmes de TiN e TiC, primeiramente sobre substratos de aços ferramenta AISI H13 e AISI D2 temperados e revenidos. Posteriormente, realizou-se o tratamento
Publicado em: 2008
-
11. Propriedades superficiais do aço AISI H13 após tratamento duplex (nitretação e (TiAIN) para moldes de injeção de alumínio
The hot-work steel AISI H13 is the most used to make molds in aluminum injection. Many studies have been made to increase its lifetime. One promising method is the duplex treatment, where the mold is submitted to a heat treatment, nitriding and coating deposition. The current work uses the titanium aluminum nitride (TiAlN). The influence of the nitrated laye
Publicado em: 2007
-
12. Efeito do carbono no processo de nitrocarburização com plasma pulsado da liga metalica AISI H13 / Carbon effect on pulsed plasma nitrocarburizing process in AISI H13 tool steel
This work presents a study on the effect of the incorporation of carbon and nitrogen on he formation of a singlephase homogeneous layer, composed by e -Fe2-3(C,N) carbonitrides, on the top surface of a AISI H13 tool steel. We also present studies on the effect of the incorporation of these elements (C and N) in the microstructure and in the mechanical and ch
Publicado em: 2007