Acrylonitrile
Mostrando 1-12 de 63 artigos, teses e dissertações.
-
1. Short Circuit and Recovery Time Tests in a helical bifilar R-SFCL module
Abstract Superconducting Fault Current Limiter (SFCL) modules with distinct arrangements have been investigated, seeking design and performance enhancements. In this context, this work aims to propose a design for resistive SFCL (R-SFCL) modules, using RE-Ba-Cu-O high-temperature superconducting tapes (HTS) wound on an alternative support material. An R-SFCL
J. Microw. Optoelectron. Electromagn. Appl.. Publicado em: 2021-06
-
2. Blue Glow Sticks: Cinnamic Acids and Arylacrylonitriles with Liquid-Crystalline Properties and Highly Fluorescent
Five new π-conjugated chromophores derived from acrylic acid and acrylonitrile were synthesized and their thermal and photophysical behaviors were analyzed. They were designed and synthesized through Knoevenagel condensations between arylacetylenebenzaldehydes and a methylene group activated from cyanoacetic and malonic acids. The characterization of the ta
J. Braz. Chem. Soc.. Publicado em: 2021-01
-
3. CONSTRUÇÃO DE UM SUPORTE AJUSTÁVEL LAB-MADE IMPRESSO EM 3D PARA MEDIÇÃO DE ÂNGULO DE CONTATO
Advances in the use of 3D printing technology have led to the development of new low-cost devices. This technology features high versatility, considering the easy modulation of the materials depending on its objectives and applications. In this sense, we have developed a laboratory-built contact angle measuring device (lab-made). The device was composed by t
Quím. Nova. Publicado em: 2020-09
-
4. Modelo de Treinamento para Inserção de Dispositivos Intrauterinos
RESUMO Introdução Aprender praticando exclusivamente em pacientes é cada vez menos aceitável no ensino médico. O ensino baseado em simulação é uma ferramenta capaz de gerar aquisição de habilidades e competências de forma eficaz e em ambiente controlado, sem causar dano ao paciente. A Ginecologia é uma especialidade médica que depende de trein
Rev. bras. educ. med.. Publicado em: 14/10/2019
-
5. Influência da concentração dos monômeros de acrilato e metacrilato de hidroxipropila na copolimerização em emulsão do estireno com acrilato de n-butila e acrilonitrila para produção de adesivos.
RESUMO Monômeros acrílicos contendo grupos hidroxila são frequentemente empregados na produção de polímeros, especialmente para aplicações em diferentes substratos ou mesmo em reações posteriores de modificação química com grupos isocianato ou carboxila. Este trabalho tem como objetivo estudar o efeito da concentração dos monômeros de acrilat
Matéria (Rio J.). Publicado em: 16/09/2019
-
6. Performance Analysis of X Band Horn Antennas using Additive Manufacturing Method Coated with Different Techniques
Abstract In this study are analyzed horn antennas to operating at X band (8 – 12 GHz) and manufactured by additive manufacturing method (AM). To construct the antennas using AM method was necessary made the structure with acrylonitrile butadiene styrene (ABS) thermoplastic using a 3D printer, and then coated the antennas with conductive surfaces. Were fabr
J. Microw. Optoelectron. Electromagn. Appl.. Publicado em: 19/06/2019
-
7. Selecting chemicals for separation of ABS and HIPS in WEEE by froth flotation
Abstract The feasibility of using common chemicals to separate plastics from waste electrical and electronic equipment (WEEE) by froth flotation is investigated. Plastic waste is one of the WEEE polluters and a separation is necessary to recycle it. The most common plastics in electronic industries are acrylonitrile-butadiene-styrene (ABS) and high impact po
Polímeros. Publicado em: 10/06/2019
-
8. Quantification by FT-IR (UATR/NIRA) of NBR/SBR blends
Abstract Rubber blends are important materials in automotive industry, as well as in other sectors. However, there are implications when suitable use of a polymer in an artifact is not made. In the automotive area, for example, the use of an elastomer without the fuel resistance requirement would result in component degradation, potential fuel leakage, and
Polímeros. Publicado em: 29/11/2018
-
9. Preparation and Characterization of Hollow Glass Microspheres- Reinforced Poly (acrylonitrile-co-butadiene-co-styrene) Composites
In this study, poly(acrylonitrile-co-butadiene-co-styrene)/hollow glass microspheres (ABS/HGM) composites were prepared by means of a twin-screw extruder. HGM were incorporated at different loadings of 2.5, 5.0, and 7.5 wt.% at the central extruder zone with different types of ABS. The morphological, physical, thermal, rheological and mechanical properties o
Mat. Res.. Publicado em: 17/09/2018
-
10. Nitrile rubber and carboxylated nitrile rubber resistance to soybean biodiesel
Abstract Biodiesel has been considered a suitable substitute for petroleum diesel, but their chemical composition differs greatly. For this reason, biodiesel interacts differently than petroleum diesel with various materials, including rubbers. Therefore, the resistance of some elastomers should be thoroughly evaluated, specifically those which are commonly
Polímeros. Publicado em: 15/03/2018
-
11. FT-IR methodology (transmission and UATR) to quantify automotive systems
Abstract When using Fourier transform infrared spectroscopy (FT-IR) under the qualitative aspect for characterization of polymer blends, often a simple identification of each one of the existing polymers in the blend does not justify the material failure since different amounts of each component may result in different mechanical properties, which should be
Polímeros. Publicado em: 15/03/2018
-
12. Calcium Phosphate Coatings by Sol-Gel on Acrylonitrile-butadiene-styrene Substrate
Additive manufacture is an effective technology to produce complex macrostructures from polymers. Sol-gel is a chemical process that affords multifunctional materials by functionalization of different substrates. This work reports on the use of acrylonitrile-butadiene-styrene polymer (ABS) as starting material to obtain a substrate by additive manufacture. C
J. Braz. Chem. Soc.. Publicado em: 2017-06