3d Cad Systems
Mostrando 1-9 de 9 artigos, teses e dissertações.
-
1. Three-dimensional assessment of internal adaptation measurement of three cad/cam ceramic systems
Resumo Este estudo teve como objetivo avaliar a adaptação interna de três diferentes coroas cerâmicas CAD/CAM (Computer-aided design/computer-aided manufacturing). A adaptação interna de um material cerâmico de rede com infiltração de polímero (Vita Enamic [VE]) foi comparada com duas cerâmicas de vidro maquináveis; silicato de lítio reforçado
Brazilian Dental Journal. Publicado em: 2022
-
2. Design and Manufacture of a Solar-Powered Unmanned Aerial Vehicle for Civilian Surveillance Missions
ABSTRACT In order to promote the development of renewable energy and take advantage of the new technologies for the benefit of sustainability, both the design and the manufacture methodologies of an experimental solarpowered unmanned aerial vehicle for civilian surveillance applications are presented. Throughout the document, it is provided the historical pr
J. Aerosp. Technol. Manag.. Publicado em: 2016-12
-
3. Geração de b-splines via FPGA / B-spline generation via FPGA
The b-splines are used in CAD/CAM/CAE systems to represent and define complex curves and surfaces, being adopted by the main computer graphics standards due to features like compact mathematic representation, flexibility and affine transformations. In 3D acquisition systems and integrated CAM-CNC systems, the use of the b-spline in the geometric information
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 10/08/2012
-
4. Control of uncertainties within an interdisciplinary design approach of a robust high heel
Within this paper the combination of several methods, developed and used in Collaborative Research Center (CRC) 805 - "Control of Uncertainties in Load Carrying Systems in Mechanical Engineering" of the DFG (German Research Foundation), is used to demonstrate the development of a load carrying system under uncertainty. The development starts with the identif
J. Braz. Soc. Mech. Sci. & Eng.. Publicado em: 2012
-
5. Possibilidades da produção artística via prototipagem rápida : processos CAD/CAM na elaboração e confecção de obras de arte e o vislumbre de um percurso poético individualizado neste ensaio / Possibilities of Art via Rapid Prototyping : using CAD/CAM systems to create art works and a glimpse of a poetic route individualized essay
Este trabalho apresenta uma pesquisa prática sobre o uso de tecnologias CAD/CAM com foco no uso de prototipagem rápida em Arte. O trabalho está organizado de modo a explicar a tecnologia empregada, apresentando uma seleção de principais artistas que se utilizam de PR para desenvolver suas obras. Por fim há uma produção poética pessoal, com a intenç
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 26/02/2010
-
6. Uso do CAD 3D na compatibilização espacial em projetos de produção de vedações verticais em edificações. / 3D CAD use in spacial compatibility analysis in production design for partition walls in buildings.
This work aims to present a proposal for 3D CAD use for production design of partition walls, including the design coordination as an inherent part of the design process. The research was organized adopting three strategies to obtain successive validations regarding the advantages of 3D CAD compared to 2D CAD use. The strategies used were: a pilot case study
Publicado em: 2007
-
7. Assessment of radiotherapic treatments with thermoluminescent dosimetry / Verificação de tratamentos radioterápicos diversos com dosimetria termoluminescente
The last decades noticed a massive improvement in radiotherapy techniques and the use of segmented beams produced by multileaf collimators. However, the dose radiation therapy planning systems (TPS) in use are characterized by the restriction of access to the calculation algorithms. The aim of this work was to compare dose values measured in an anthropomorph
Publicado em: 2007
-
8. o uso do paradigma restrições geométricas para apoio a projetos de instalações elétricas / Using geometric constraint approach to support electri- cal installation design
Nowdays, a growth has been observing in the software use CAD (Computer-Aided Design) and CAE (Computer-Aided Engineering) for design in area of the architecture, engineering and building . The professional makes use of those tools that automate and accelerate design routines propitiating more time to improve the quality of them. However, most of the current
Publicado em: 2006
-
9. Automação do processo de modelamento e detalhamento de estruturas pré-moldadas de concreto armado via tecnologia CAD e programação orientada a objetos
This Master Dissertation presents the design and implementation of a CAD (Computer Aided Design) system for automation of some steps of the process of modeling and detailing of pre-molded concrete structures, based on solid modeling. This system is implemented using the Object Oriented Programming paradigm (OOP) with the C++ language, using AutoCAD 2002 as t
Publicado em: 2002