Shielding Gas
Mostrando 1-12 de 33 artigos, teses e dissertações.
-
1. Efeito da Adição de Propileno aos Gases de Proteção Convencionais na Soldagem GMAW Aplicada a Juntas de Topo e Ângulo
Resumo O presente trabalho teve por objetivo avaliar a adição de 1,3% de C3H6 ao CO2 puro e 0,6% de C3H6 à mistura de Ar+25%CO2, na soldagem de aço carbono utilizando o processo Gas Metal Arc Welding (GMAW) aplicado em juntas de topo com chanfro em V e ângulo em T. As soldas foram realizadas utilizando chapas de aço SAE 1020, arame de solda ER70S-6 de
Soldag. insp.. Publicado em: 02/12/2019
-
2. Influência da composição do gás de proteção nas tensões residuais de juntas de aço DP600 soldadas pelo processo GMAW
RESUMO A indústria automobilística vem investindo em novos processos de fabricação que melhoram a produtividade sem perda da qualidade. Entretanto, a presença de tensões residuais, geradas em todos os processos de fabricação, constitui um dos grandes problemas encontrados na indústria metal mecânica, pois estas podem se somar às tensões de carreg
Matéria (Rio J.). Publicado em: 16/09/2019
-
3. Effect of Nitrogen Addition to Shielding Gas on Cooling Rates and in the Microstructure of Thin Sheets of Duplex Stainless Steel Welded by Pulsed Gas Tungsten Arc Welding Process
The effect of the nitrogen content in the shielding gas and its effect on temperature distributions at the welded zone of thin sheets of duplex stainless steel have been evaluated. The duplex stainless steels have many features due to unique microstructural combination of austenite and ferrite grains. The phase balance can be easily shifted depending on the
Mat. Res.. Publicado em: 26/08/2019
-
4. Influência da composição do gás de proteção nas tensões residuais de juntas de aço DP600 soldadas pelo processo GMAW
RESUMO A indústria automobilística vem investindo em novos processos de fabricação que melhoram a produtividade sem perda da qualidade. Entretanto, a presença de tensões residuais, geradas em todos os processos de fabricação, constitui um dos grandes problemas encontrados na indústria metal mecânica, pois estas podem se somar às tensões de carreg
Matéria (Rio J.). Publicado em: 20/05/2019
-
5. Investigation on the Wear Properties of Ti/TiC/TiN Composite Coatings Prepared by Powder Cored Wires Through TIG Method at Nitrogen Atmosphere on Titanium Substrate
In this present study, Tungsten Inert Gas (TIG) welding and powder filled cored wires with nitrogen shielding gas were utilized to produce TiC and TiN surface composite coatings on the titanium (Ti) sheet substrate. The TIG procedure was done at same welding parameters for all of prepared samples. Phase analysis and microstructures were done by X-ray Diffrac
Mat. Res.. Publicado em: 15/04/2019
-
6. Efecto de la Composición Química del Metal de Aporte y del Calor Aportado Sobre la Microestructura y las Propiedades Mecánicas de Juntas Soldadas de Aceros Inoxidables Dúplex
Abstract Duplex stainless steels are characterized by good weldability and mechanical properties; they also present a high resistance to general and localized corrosion. They are the main materials when welding pipes with high requirements in different industries, mainly oil and gas. These steels have a microstructure consisting of two phases: 50% austenite
Soldag. insp.. Publicado em: 2017-06
-
7. Efecto del Gas de Protección, Ángulos de Trabajo y Desplazamiento sobre las Características de Juntas de Filete Obtenidas por GMAW en un Acero Microaleado de Alta Resistencia
Abstract: The fillet joint is one of the most used in several industries, particularly in the agricultural machinery. However, many times, the complexity of the parts to be joined difficult welder accessibility, therefore working and travel angles are important variables to analyze. Furthermore, in GMAW process, employing shielding gas mixture Ar-20%CO2 has
Soldag. insp.. Publicado em: 2016-09
-
8. Gaseous Shielding Gas Additives as Flux Substitute for TIG Arc Brazing
Abstract Brazing is one of the key technologies in the field of joining of metal components. To improve the wetting of brazing material and work-piece surface, it is often required to fall back on the use of flux. The application of these substances requires accuracy and is often connected with considerable expenditure and it is, just as the removal of flux
Soldag. insp.. Publicado em: 2015-09
-
9. Efecto de los parámetros de soldadura sobre la microestructura de recargues nanoestructurados base hierro depositados por FCAW-S
Lately modern hardfacing tubular wires for semiautomatic welding with gas protection and without it have been developed. These wires deposit Fe-based nanostructured alloys with high abrasive wear resistance. The information on these new consumables is scarce, especially about the effect that the welding parameters (heat input, shielding gas, arc voltage, cur
Soldag. insp.. Publicado em: 2014-12
-
10. Estudo da influência dos parâmetros no processo de soldagem GMAW - arco pulsado
Pulsed gas metal arc welding describes the metal transfer mode involving oscillation (pulsing) of the welding current from a high pulse current in which level drop growth, necking of wire tip and detachment occur, and a low background current, which is applied to maintain the arc. The advantages of the process are: metal transfer without spatter formation an
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 29/09/2011
-
11. Análise Comparativa dos Processos de Soldagem GMAW e FCAW com Transferência Metálica por Curto-Circuito na Posição Horizontal / Comparative Analysis of Processes Welding FCAW and GMAW Metal Transfer to Short-Circuit in a Horizontal Position
Os processos de soldagem com arame maciço (GMAW) e arame tubular (FCAW), processos que competem entre si em termos de qualidade, produtividade e operacionalidade, necessitam de informações seguras de suas principais características e aplicações para uma determinada condição de soldagem. Desta forma, o objetivo deste trabalho é comparar a potencialid
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 29/08/2011
-
12. Aplicabilidad del monitoreo de emisiones del arco eléctrico para el control de calidad en el proceso MAG-S
Ensuring quality in welding is not a trivial task. For this purpose several quality control checks are performed, at the expense, costs and production times are increased. There are several automated welding systems and they are assisted by control systems based on monitoring of welding parameters. However, automated quality monitoring systems are limited an
Soldagem & Inspeção. Publicado em: 2011-12