Physical Metallurgy
Mostrando 1-12 de 13 artigos, teses e dissertações.
-
1. Analysis of the densification of a composite obtained by sintering process of aluminum bronze powders with different carbides
Abstract Aluminum bronze alloy is applied in environments that require materials of high mechanical resistance and wear, such as marine, oil & gas and aerospace ones. This study analyzes the densification of composites based on aluminum bronze with additions of the vanadium (VC) and niobium (NbC) carbides, and the influence of these carbides in the milling e
REM, Int. Eng. J.. Publicado em: 19/06/2019
-
2. Obtención de compuesto de titanio con gradiente de porosidad mediante técnica pulvimetalúrgica
ABSTRACT Within the study of biomaterials for implantological use titanium is among the most widely employed metals due to its excellent corrosion and mechanical resistance. In spite of the advances made, there are some issues remaining with the value of the elastic moduli of the titanium (110GPa) in comparison with the elastic moduli of the cortical bone (2
Matéria (Rio J.). Publicado em: 19/07/2018
-
3. Materials Selection of Optimized Titanium Alloys for Aircraft Applications
The aim of the present work was to explore the correlation between the physical metallurgy of titanium alloys and its main attributes to select optimized materials for structural aircraft applications in the landing gear beam. The Ashby's method was employed as the materials selection strategy to consolidate and evaluate the data collected from the current l
Mat. Res.. Publicado em: 19/02/2018
-
4. Quality management system implementation for fracture toughness testing
Abstract The evaluation of material fracture mechanic properties has had an increasing need, especially in the oil and gas industries. This scenario requires quality assurance of fracture toughness tests. This article describes the activities carried out when implementing the Quality Management System (QMS) for the fracture toughness tests at the Physical Me
Rem: Rev. Esc. Minas. Publicado em: 2016-03
-
5. Influence of Milling Time During the Mechanical Alloying Process on the Properties of Fe-3Si-0.75P Alloy
AbstractIn this study the soft magnetic alloy Fe-3Si-0.75P (wt%) was obtained by mechanical alloying through powder metallurgy. The processing included the formulation of metallic powder, wet milling for 1 h, 3 h, 6h and 9 h, in an attritor mill using alcohol P.A. as a lubricant. Cold compaction was then performed in a floating die under 600 MPa pressure and
Mat. Res.. Publicado em: 2015-10
-
6. Estudo da microestrutura, da textura cristalográfica e da recristalização em chapas obtidas por lingotamento contínuo e semicontínuo da liga de alumínio AA4006. / A study of the microstructure, crystallographic texture, and recrystallization in AA4006 alloy strips produced by twin roll caster and direct chill processes.
A liga de alumínio designada AA4006 é muito utilizada na indústria. É uma liga do sistema Al-Fe-Si, com teores (% em massa) de Si na faixa de 0,8 a 1,2% e Fe entre 0,5 e 0,8%. Apesar de ser bastante utilizada, ela foi pouco estudada. Neste trabalho foi realizado um estudo comparativo da microestrutura e da textura cristalográfica entre chapas da liga AA
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 29/02/2012
-
7. Determinação do tempo de mistura numa panela siderúrgica
A eficiência do processo de fabricação do aço durante a etapa de refino secundário na panela está relacionada aos fenômenos de mistura. Em função disto, é de muito interesse o conhecimento do estado de mistura que ocorre durante o tratamento do aço líquido na panela tendo em vista a otimização do processo. Assim sendo, o presente estudo tem com
Publicado em: 2010
-
8. Avaliação da seqüência de transformações de fases do aço AISI 430 convencional. / Characterization of the phase transformations sequence for conventional AISI 430 steel.
Este trabalho visa caracterizar a seqüência de precipitação do aço inoxidável ferrítico do tipo AISI 430 convencional, durante a etapa de laminação a quente. Esta caracterização foi realizada através do estudo de três condições industriais e de seis condições tratadas termicamente. Todas as amostras foram avaliadas por microscopia ótica e e
Publicado em: 2010
-
9. Work hardening and recrystallization of high speed AISI M2 and ABC III: a comparative study. / Encruamento e recristalização dos aços rápidos AISI M2 e ABC III: um estudo comparativo.
O objetivo deste trabalho é realizar um estudo comparativo da recristalização de dois aços rápidos, AISI M2 (Werkstoffnummer 1.3343) e ABC III (Werkstoffnummer 1.3333), após o encruamento resultante do processo de laminação a frio de chapas planas utilizadas para a confecção de serras fitas. Estudar a recristalização estática nesta classe de aç
Publicado em: 2008
-
10. Age-hardening of Ti-35Nb-7Zr-5Ta alloy for orthopaedic implants
Bone injuries and failures often require the inception of implant biomaterial. Research in this field has received increasing attention recently. In particular, porous metals are attractive due to its unique physical, mechanical, and new bone tissue ingrowth properties. The aim of this work is to investigate age hardening behavior of Ti-35Nb-7Zr-5Ta alloy pr
Materials Research. Publicado em: 2007-09
-
11. Resíduos de mineração e metalurgia: efeitos poluidores em sedimentos e em espécie biomonitora - Rio Ribeira de Iguape - SP / Residues of mining and metallurgy: pollutant effect in sediments and biomonitor organism - River Ribeira de Iguape
For approximately 40 years, Ribeira de Iguape River received mining wastes (enriched in Cu, Cr, Pb, Ag and Zn) and metallurgical slags (enriched in Cu, Zn, Cr, Fe, Pb and As), produced and discharged by Plumbum S/A, a company located in Adrianópolis (Paraná). In order to verify the contribution of these residues in the river contamination and natural purif
Publicado em: 2007
-
12. Caracterização de revestimentos de hidroxiapatia depositados por aspersão termica a plasma sobre a liga Ti-13Nb-13Zr para aplicação em implantes dentarios
The Ti-13Nb-13Zr alloy has been proposed as a new metallic biomaterials wich stands out for introducing in its fonnulation three of the four metallic elements of larger biocompatibility (Ti, Nb, Zr, Ta), besides introducing, low elasticity modulus and excellent corrosion resistance. The Ti-13Nb-13Zr alloy was obtained from powder metallurgy. Substrates of th
Publicado em: 2004