Corrosion Testing
Mostrando 1-12 de 38 artigos, teses e dissertações.
-
1. Effect of High-pressure Torsion on Corrosion Behavior of a Solution-treated Al-Mg-Sc Alloy in a Saline Solution
The effect of the increase in crystalline defects in the structure generated by high-pressure torsion (HPT) on the corrosion behavior of metallic materials is not well understood. This report evaluates the influence of HPT on the corrosion behavior of a solution treated Al-3wt% Mg-0.2wt% Sc alloy in a 3.5 wt./v.% NaCl solution. The electrochemical behavior o
Mat. Res.. Publicado em: 04/11/2019
-
2. The importance of corrosion resistance test of cannulas in the quality control of hypodermic needles
According to Anvisa risk rating, hypodermic needles offer medium risk to the user’s health. This study discussed the importance of the corrosion resistance test in tubes of hypodermic needles, in the product quality control. A review of cannulas of hypodermic needles was carried out according to ISO 9626:2003 and 9259:1997 ABNT NBR. For the results evaluat
Braz. J. Pharm. Sci.. Publicado em: 24/10/2019
-
3. Revisão sobre ensaios acelerados para indução da corrosão desencadeada por cloretos em concreto armado
Resumo A corrosão de armaduras desencadeada por cloretos é um dos principais problemas que afetam as estruturas de concreto armado. Considerando o estudo desse tipo de problema, a velocidade na coleta dos dados, a possibilidade de controle das variáveis que influenciam o processo de corrosão e o baixo custo na realização dos testes têm sido aspectos m
Ambient. constr.. Publicado em: 03/10/2019
-
4. Effect of Sigma Phase Precipitated at 850 °C on Corrosion Behaviour of UNS S82441 Duplex Stainless Steel
ABSTRACT Duplex stainless steels (DSS) are alloys with binary microstructure consisting of ferrite (δ) and austenite (γ), combining high mechanical properties and corrosion resistance by pitting and stress corrosion, due to the two phases austenite/ferrite. However, the formation of secondary and intermetallic phases, during solidification processes, heat
Matéria (Rio J.). Publicado em: 16/09/2019
-
5. Lime Addition Effect on Corrosion of Reinforced Mortar
ABSTRACT This study aims to investigate the effect of lime addition in cement mortar on corrosion resistance of carbon and galvanized steel reinforcements. Mixed mortars were studied containing three contents of lime (6.7, 13.3, and 26.3 wt.%). The water retention, incorporated air, and compression strength of reinforced mortars were determined. Immersion te
Matéria (Rio J.). Publicado em: 16/09/2019
-
6. Investigating the Effect of Curing in the Chloride Diffusion Coefficient of Conventional Concrete
Concrete is the most used material in the construction industry worldwide. Built concrete infrastructure is exposed to specific environments conditions during the asset’s life, which impose chemical and physical actions that may lead to premature deterioration. Poor concrete durability and corrosion of reinforcement bars are the primary cause of structural
Mat. Res.. Publicado em: 16/09/2019
-
7. Effects of Gas Nitriding on Fatigue and Crack Initiation of Ti6Al4V produced by Selective Laser Melting
Selective laser melting (SLM) is an additive manufacturing technique which permits fabrication of three dimensional parts by selectively melting consecutive layers of metallic powder. This allows the production of parts with high geometrical complexity. Titanium alloy Ti-6Al-4V (Ti64) is widely used in industry due to its high strength-to-mass ratio, corrosi
Mat. Res.. Publicado em: 15/07/2019
-
8. A New methodology of Nondestructive Testing for Quantitative Evaluation of Sigma Phase in Duplex Stainless Steels
Duplex Stainless Steels (DSSs) are widely used in the oil and gas industry. When the steel is subjected to a thermal gradient, as in welding may occur precipitation of intermetallic phases. Among these phases, there is the sigma phase, which even in small quantities reduces drastically the mechanical and corrosion resistance properties. According to some stu
Mat. Res.. Publicado em: 13/05/2019
-
9. Corrosión atmosférica acelerada en una fundición gris ASTM A48
ABSTRACT Due to the long times required to investigate atmospheric corrosion resistance of metals, data on the subject is scarce. One of these studies is the one made by Southwell et al., where the effect of corrosion in a cast gray iron during 16 years was studied in various environments. This research shows and discusses the behavior of cast gray iron when
Matéria (Rio J.). Publicado em: 19/07/2018
-
10. Corrosion Behavior of Plasma Nitrided and Nitrocarburised Supermartensitic Stainless Steel
Supermartensitic stainles steels (SMSS's) are a new generation of martensitic steels that have been increasingly used in oil and gas applications due to their adequate corrosion resistance and mechanical properties. In the present study, SMSS specimens (UNS S41425) were solution heat treated and air cooled followed by plasma nitriding and nitrocarburising at
Mat. Res.. Publicado em: 12/03/2018
-
11. Evaluation of the Influence of Surface Finishing on the Corrosion Resistance of HVOF Applied Inconel 625 Coatings on Steel
In this work, the corrosion resistance of Inconel 625 coatings applied to AISI 4140 steel plates was evaluated. Coatings were produced by High Velocity Oxygen Fuel (HVOF) by use of two different equipment which use either kerosene (liquid) or propane (gas) as fuel. The resulting coatings were evaluated in two conditions: as-deposited and after a surface fini
Mat. Res.. Publicado em: 18/12/2017
-
12. Comportamiento bi-modal de una fundición gris y un acero estructural al carbono en corrosión atmosférica marina acelerada
ABSTRACT According to data gathered in the last Metal Foundry Industrial Production Survey [1], approximately 46% of the industrial production of ferrous alloys is gray-iron. In this context the study of the atmospheric corrosion resistance of gray-iron becomes interesting to asset its useful life when subject to weathering conditions. The studies of gray-ir
Matéria (Rio J.). Publicado em: 22/06/2017