Composite Beams
Mostrando 1-12 de 86 artigos, teses e dissertações.
-
1. Numerical formulation for nonlinear analysis of concrete and steel shells with deformable connections
Abstract A two-dimensional interface finite element capable of associating flat shell elements positioned one above the other was developed. The implemented interface element can physically simulate the contact between the flat shell elements and connect the reference planes of the shell elements above and below it. The formulation presented allows considera
REM, Int. Eng. J.. Publicado em: 2021-09
-
2. Numerical analysis of collapse modes in optimized design of alveolar Steel-concrete composite beams via genetic algorithms
Abstract The objective of this study is to present the formulation and applications of the optimization problem of steel-concrete composite alveolar beams. In addition to presenting the formulation, a comparative analysis of the predominant collapse modes is performed numerically via the finite element method. The optimization program was developed with the
REM, Int. Eng. J.. Publicado em: 2021-06
-
3. Composite floor system with CFS trussed beams, concrete slab and innovative shear connectors
Abstract Steel and concrete floor systems are widely applied for buildings and provide excellent structural response, optimized material consumption, reduced beam height, and improved bending strength and stiffness capacity. In recent years, many experimental investigations concerned with new alternatives addressed to efficient interaction between steel and
REM, Int. Eng. J.. Publicado em: 2020-03
-
4. Number of laminae on the mechanical behavior of glued laminated timber (glulam) of Toona ciliata produced with vegetable polyurethane adhesive
RESUMO A madeira laminada colada (MLC) é um material compósito obtido a partir da colagem de lâminas de madeira dispostas com as fibras paralelas entre si. O objetivo deste trabalho foi avaliar a influência do número de lâminas no comportamento mecânico de MLC de Toona ciliata produzidas com adesivo poliuretano de base vegetal. As vigas de MLC foram p
Ciênc. agrotec.. Publicado em: 20/12/2019
-
5. Optimized dimensioning of steel-concrete composite beams
Resumo As seções mistas de aço e concreto estão cada vez mais sendo utilizadas na construção civil, tanto no cenário mundial quanto no Brasil. O trabalho conjunto do perfil de aço e da laje de concreto aumenta consideravelmente o desempenho do elemento estrutural misto devido ao aproveitamento das vantagens de cada material. Neste trabalho, é utiliz
Rev. IBRACON Estrut. Mater.. Publicado em: 13/12/2019
-
6. About the use of semi-continuity in simply supported composite steel and concrete beams, to remove fireproof coatings for standard-fire resistance requirement of less than 30 minutes
Resumo Estudos anteriores do comportamento sob ação do incêndio de vigas mistas de aço e concreto, sem instabilidades locais (ditas compactas), considerando a rigidez à flexão nos apoios fornecida pela armadura negativa longitudinal à viga (semicontinuidade), mostraram que não é possível justificar a ausência de revestimento contra fogo para tempo
Rev. IBRACON Estrut. Mater.. Publicado em: 11/11/2019
-
7. Experimental evaluation on the structural behavior of truss shear connectors in composite steel-concrete beams
Resumo As estruturas mistas apresentam grandes vantagens quanto a aspectos estruturais e construtivos, sendo os conectores de cisalhamento determinantes para a obtenção da interação entre os elementos estruturais e para a distribuição dos esforços na estrutura, aproveitando-se de forma efetiva da potencialidade de cada material constituinte da estrutu
Rev. IBRACON Estrut. Mater.. Publicado em: 11/11/2019
-
8. Some Aspects of Numerical Modeling of Steel-Concrete Composite Beams with Prestressed Tendons
Abstract Aspects about the numerical modeling of three-dimensional prestressed steel-concrete composite beams by using the finite element (FE) method are highlighted and commented in this work. Emphasis is given to the numerical treatment of bonded and unbonded tendons. The proposed modeling technique uses curved beam and catenary elements for simulating int
Lat. Am. j. solids struct.. Publicado em: 15/08/2019
-
9. Plate with holes as shear connector in cold formed steel composite beams
Resumo Buscando compatibilizar as estruturas em perfil formado a frio com os sistemas de piso com pré-laje, foi proposta nesse trabalho uma alternativa de conector de cisalhamento para vigas mistas compostas por perfil formado a frio que visa maximizar a área disponível para apoio das pré-lajes durante o processo construtivo. Trata-se de um conector em c
Rev. IBRACON Estrut. Mater.. Publicado em: 18/07/2019
-
10. Structural Behaviour of Cold-Formed Steel of Double C-Lipped Channel Sections Integrated with Concrete Slabs as Composite Beams
Abstract Cold-formed steel (CFS) construction is widely recognised as an important contributor to sustainability and green construction. Thus, the use of CFS construction is encouraged and had been advanced by innovations in its structural applications. One such innovation that has recently gained popularity is the use of CFS sections in composite constructi
Lat. Am. j. solids struct.. Publicado em: 27/06/2019
-
11. Evaluation of bulk-fill systems: microtensile bond strength and non-destructive imaging of marginal adaptation
Abstract The objective of this study was to investigate microtensile bond strength (MTBS) and interfacial adaptation (IA) of bulk-fill restorative systems bonded to dentin in Class-I-preparations. Box-shaped preparations (4-mm-long, 3-mm-wide, 2-mm-high) made in extracted molars, and Teflon matrix with the same dimensions positioned over the occlusal surface
Braz. oral res.. Publicado em: 06/08/2018
-
12. Finite element modelling to assess the effect of position and size of the piezoelectric layer of a hybrid beam
Abstract A one dimensional finite element model is presented to assess the effect of position and size of the piezoelectric layer of a hybrid beam. The efficient layerwise (zigzag) theory is used for making the finite element model. The 1D beam element has eight mechanical and a variable number of electrical degrees of freedom. The codes are developed in Ma
Lat. Am. j. solids struct.. Publicado em: 03/05/2018